Brian's Questions: I've recently walled off the third bay of my three car garage to give me a smaller space to heat and a wall to work with. I have started thinking about my ~270 sqft shop in three dimensions trimming all the fat and maximizing my functionality.What would you guys do with a nice healthy 11ft ceiling height considering I want pretty much my entire shop to exist is this space. What type of ideas would you have for multi functioning furniture? What would you put on the walls? Everything that can be is already on wheels. I've got most every major tool you guys do. Just curious on your take. How would you cram yourselves into this little space or do you already? Thanks for continuing the podcast. -Jim G.  I am building an outdoor bench using steel legs and a currently  rough cedar top. I plan on sanding the cedar smooth and finishing it. What would be the best grit to sand to, and what finish should I apply? It will get all-day full sunlight. Jason H. Guy's Questions: Hi:  As I have said before, this is the best woodworker podcast on the planet!  I enjoy so much the focus on woodworkers questions.  Your personalities shines through as well as your intellect and your skills as a woodworker.  Thanks so much. My question stems from a recent project I started.  I tried to be more exacting.  I designed the project on gridded paper, figured out each exact dimension and then started to calculate the wood requirements.  I figured out the sheet goods by figuring out the rough layout of the parts on a scale grid diagram.  Then I calculated the board feet of each of the solid wood parts using a board feet calculator app a selecting 10% for waste option.  I then added them up and got ready to buy the necessary wood. In the past I just winged it.  I'd have a rough drawing on scrap paper and a guess at the wood requirements which often meant follow-up trips to the store.  Projects often had a few rework, redesign elements on the fly and some issues that hopefully I could only see, hence the change to more exacting. I have a few questions.  How exact are you with your designs?  Is this the process you go through before purchasing wood?  Is there another way?  Do you use any apps like:"BoardFeetEasy" or "SmartCut"?  Do you use any other woodworking apps?  If so which ones?  Is 10% a good waste figure?  Do you adjust the waste figure based on any criteria?  What are the criteria? Thanks again for you're time, focus and insite into the craft of woodworking. Regards,Joe James Hi, thanks for all the great work on this podcast. Yours is the only one that actually I even have a dedicated podcast app set up for, so that you guys are only a couple taps away for my sausage fingers whenever I have a free moment and want to learn something.  Anyway, my question is about using a dryer plug for 220V machines. I'm planning a couple new tools for my basement shop, and whilst my first choice is to add a dedicated 220 line, I'd rather space things out financially if I can. One option seems potentially to use the dryer electrical socket until I have the cash flow to run dedicated electrics. I'm seeing mixed things in my research and wondering if you have any real world experience on using dryer plugs for tools with an adapter/extension, specifically if it's a hazard and the pros/cons? In my case the tools would be a Hammer A326 and Sawstop PCS 3HP. Thanks for any advice you can offer and keep up the great work. Phil Evans Huy's Questions: Hi guys, love the podcast! Thanks for all you do! I’m designing my first piece of larger furniture, an entry way table. I am planning 3 drawers across the top, and below that a cabinet in the center and open shelves to either side. I’m wondering how you guys decide on proportions for a build like this. Supposedly the 1.618 is some kind of magic formula that makes everything perfect, but how do you use it, or do you even bother? What if the piece has to fit a certain space, do you take that into account? Help me woodshop life, you’re my only hope! Matt Hello all, how about another shop storage question? I’ve been primarily a power tool user for many years, but have started building a hand tool collection over the last 2 or 3 years. Im finding the “hybrid” approach more to my liking and feel it’s certainly improved the quality of my projects with the ability to fine tune fit and finish. Now being the proud owner of quality chisels, a few hand planes, scrapers and so on, most of the tools are in a tool box drawer.  I want to get these commonly used items out of the drawer and in reach, but I find myself starting to plan and build tool holders or storage solutions only to scrap it and move onto something else because I get lost in how simple or complex to make it.  I need to just shut up and do it, I know this. In your opinions, when you need a storage solution, do you just make whats basic and functional and after some use fine tune or remake it when needed? Or, do you spend time laying everything out and aiming for a one and done build? -Mike

Brian's Questions: I've recently walled off the third bay of my three car garage to give me a smaller space to heat and a wall to work with. I have started thinking about my ~270 sqft shop in three dimensions trimming all the fat and maximizing my functionality.What would you guys do with a nice healthy 11ft ceiling height considering I want pretty much my entire shop to exist is this space. What type of ideas would you have for multi functioning furniture? What would you put on the walls? Everything that can be is already on wheels. I've got most every major tool you guys do. Just curious on your take. How would you cram yourselves into this little space or do you already? Thanks for continuing the podcast. -Jim G. I am building an outdoor bench using steel legs and a currently  rough cedar top. I plan on sanding the cedar smooth and finishing it. What would be the best grit to sand to, and what finish should I apply? It will get all-day full sunlight. Jason H. Guy's Questions: Hi:  As I have said before, this is the best woodworker podcast on the planet!  I enjoy so much the focus on woodworkers questions.  Your personalities shines through as well as your intellect and your skills as a woodworker.  Thanks so much. My question stems from a recent project I started.  I tried to be more exacting.  I designed the project on gridded paper, figured out each exact dimension and then started to calculate the wood requirements.  I figured out the sheet goods by figuring out the rough layout of the parts on a scale grid diagram.  Then I calculated the board feet of each of the solid wood parts using a board feet calculator app a selecting 10% for waste option.  I then added them up and got ready to buy the necessary wood. In the past I just winged it.  I'd have a rough drawing on scrap paper and a guess at the wood requirements which often meant follow-up trips to the store.  Projects often had a few rework, redesign elements on the fly and some issues that hopefully I could only see, hence the change to more exacting. I have a few questions.  How exact are you with your designs?  Is this the process you go through before purchasing wood?  Is there another way?  Do you use any apps like:"BoardFeetEasy" or "SmartCut"?  Do you use any other woodworking apps?  If so which ones?  Is 10% a good waste figure?  Do you adjust the waste figure based on any criteria?  What are the criteria? Thanks again for you're time, focus and insite into the craft of woodworking. Regards,Joe James Hi, thanks for all the great work on this podcast. Yours is the only one that actually I even have a dedicated podcast app set up for, so that you guys are only a couple taps away for my sausage fingers whenever I have a free moment and want to learn something.  Anyway, my question is about using a dryer plug for 220V machines. I'm planning a couple new tools for my basement shop, and whilst my first choice is to add a dedicated 220 line, I'd rather space things out financially if I can. One option seems potentially to use the dryer electrical socket until I have the cash flow to run dedicated electrics. I'm seeing mixed things in my research and wondering if you have any real world experience on using dryer plugs for tools with an adapter/extension, specifically if it's a hazard and the pros/cons? In my case the tools would be a Hammer A326 and Sawstop PCS 3HP. Thanks for any advice you can offer and keep up the great work. Phil Evans Huy's Questions: Hi guys, love the podcast! Thanks for all you do! I’m designing my first piece of larger furniture, an entry way table. I am planning 3 drawers across the top, and below that a cabinet in the center and open shelves to either side. I’m wondering how you guys decide on proportions for a build like this. Supposedly the 1.618 is some kind of magic formula that makes everything perfect, but how do you use it, or do you even bother? What if the piece has to fit a certain space, do you take that into account? Help me woodshop life, you’re my only hope! Matt Hello all, how about another shop storage question? I’ve been primarily a power tool user for many years, but have started building a hand tool collection over the last 2 or 3 years. Im finding the “hybrid” approach more to my liking and feel it’s certainly improved the quality of my projects with the ability to fine tune fit and finish. Now being the proud owner of quality chisels, a few hand planes, scrapers and so on, most of the tools are in a tool box drawer.  I want to get these commonly used items out of the drawer and in reach, but I find myself starting to plan and build tool holders or storage solutions only to scrap it and move onto something else because I get lost in how simple or complex to make it.  I need to just shut up and do it, I know this. In your opinions, when you need a storage solution, do you just make whats basic and functional and after some use fine tune or remake it when needed? Or, do you spend time laying everything out and aiming for a one and done build? -Mike

Small Shop Layout, Woodworking Software, Tool Storage and MORE!

Brian's Questions: Hey Fellas,   I’m in the market for a new table saw. I am coming from a 2hp Grizzly hybrid saw with a broken part I cannot find a replacement for. I’m debating between a 3hp Powermatic or Sawstop. Either of these will be a major upgrade from what I have but do you have opinions either way? The Sawstop technology is great and I understand accidents can happen but I tend to think if your hands are that close to the blade you’ve got bigger problems. That said, the Sawstop is up to $1,000 cheaper than the powermatic depending which add-ons you choose. Do you have any thoughts or are there other brands I’m missing and should look into? Chris  Instagram: @custom_by_chris Hi guys!  I am a hobbyist/turning professional woodworker based in Portland, Oregon.  I have really enjoyed listening to your podcast and thought I would quickly ask your opinion on rectangular dominos.  I have been creating shop-made dominos to save money.  Creating them is a pain in the butt!  Trying to nail metric round-overs with imperial bits at that level of precision is pretty involved.  It usually takes a bit of time and wasted material to set the router table up correctly in order to batch a bunch out.  Then running a glue groove on everything is another step that takes time.  A thought came to me about creating square edged, rectangular tenons that aren't hitting the radii of the domino mortise.  My thought is that the few millimeters of void wouldn't really affect the strength of the joint and the voids themselves would act as a hydrolock prevention by nature.  Assuming these aren't used for through style tenons, do you see any issues using rectangular stock?  Thanks for doing the podcast and I look forward to future episodes! Sal Al-Sudairy sfapdx@gmail.com @oregon_woodworks    Instagram Guy's Questions: Hey Guy’s  I know finishing gets hit often but this is perhaps a different spin. My basement garage is my workshop so odor and chemical safety is a concern.   I’m mostly done with my plywood/poplar painted dresser (thanks for the tips by the way, screwing and glueing without fancy jointery made assembly a breeze Guy).  That being said what is a good low odor option for finishing a paint grade project that’s being painted white? Yellowing and tannin bleed are therefore both concerns.   I’ve heard Ya’ll talk about conversion varnishes but also heard complaints about odor. Would BIN water based primer under enamel paint be best? Should I go the oil based primer/paint route for durability?   I have recently gotten a paint sprayer but am open to rolling if that’s preferable. I’ll attach my budget sprayer below for context.   Thanks so much, this is by far the best woodworking podcast.  -Dave Hello Huy, Guy, and Brian! You gentlemen, as well as Sean, have been a huge help and inspiration to my woodworking journey. Keep the great content coming! I recently picked up an older Bosch 1615 evs plunge router mounted to an old tabletop with an Incra Intelli fence. While I can find manuals online for both of these discontinued items, I'd like to get your input on how to best set up an older router with this fence. Since this particular router is in its own molded housing, I don't think a router lift is an option. What do you all recommend for setting this router up in a new table? I intend to likely build a stand-alone router table with a top made with melamine left over from a recent project, but I'm open to suggestions. Thanks, -Kurt Huy's Questions: Hi everyone,  Thank you for a great show. I've listened through the entire catalog twice, learning a lot.  In Episode #115 (and other episodes) you mention UV light turning walnut orange. I recently built a large dining room table out of walnut. I did not dye the table, even though I knew color change was possible. I have never used dye and the walnut was so stunning, I was afraid I would mess it up.  If my table turns orange, can it be sanded off? How deep does the UV "damage" go into the wood?  If I was to dye the walnut, could you please remind us what color dye you have used that works on walnut? How you have applied it to walnut, and when in the finishing process? hanks again for a great show and a great woodworking education.  Kevin Hello Gentleman,   Love the podcast. Thanks for all your hard work.  I am considering tackling a Entertainment unit for my bonus room; however I am struggling with material choice. The cabinet finish will be painted, do you suggest plywood or MDF? I plan on building some drawers with plywood boxes and MDF faces but I am concerned about the durability of the MDF when installing hinges if I use it for the carcass construction.  The overall length of this build is 16" long by 8' tall with drawers along the bottom open shelving on either side of that with the TV in the middle. Normally I am not so indecisive ; however this is such a large project and with the high cost of materials I want to start off on the right foot. Any guidance would be appreciated.  - Mike

Brian's Questions: Hey Fellas,   I’m in the market for a new table saw. I am coming from a 2hp Grizzly hybrid saw with a broken part I cannot find a replacement for. I’m debating between a 3hp Powermatic or Sawstop. Either of these will be a major upgrade from what I have but do you have opinions either way? The Sawstop technology is great and I understand accidents can happen but I tend to think if your hands are that close to the blade you’ve got bigger problems. That said, the Sawstop is up to $1,000 cheaper than the powermatic depending which add-ons you choose. Do you have any thoughts or are there other brands I’m missing and should look into? Chris  Instagram: @custom_by_chris Hi guys!  I am a hobbyist/turning professional woodworker based in Portland, Oregon.  I have really enjoyed listening to your podcast and thought I would quickly ask your opinion on rectangular dominos.  I have been creating shop-made dominos to save money.  Creating them is a pain in the butt!  Trying to nail metric round-overs with imperial bits at that level of precision is pretty involved.  It usually takes a bit of time and wasted material to set the router table up correctly in order to batch a bunch out.  Then running a glue groove on everything is another step that takes time.  A thought came to me about creating square edged, rectangular tenons that aren't hitting the radii of the domino mortise.  My thought is that the few millimeters of void wouldn't really affect the strength of the joint and the voids themselves would act as a hydrolock prevention by nature.  Assuming these aren't used for through style tenons, do you see any issues using rectangular stock?  Thanks for doing the podcast and I look forward to future episodes! Sal Al-Sudairy sfapdx@gmail.com @oregon_woodworks    Instagram Guy's Questions: Hey Guy’s  I know finishing gets hit often but this is perhaps a different spin. My basement garage is my workshop so odor and chemical safety is a concern.   I’m mostly done with my plywood/poplar painted dresser (thanks for the tips by the way, screwing and glueing without fancy jointery made assembly a breeze Guy).  That being said what is a good low odor option for finishing a paint grade project that’s being painted white? Yellowing and tannin bleed are therefore both concerns.   I’ve heard Ya’ll talk about conversion varnishes but also heard complaints about odor. Would BIN water based primer under enamel paint be best? Should I go the oil based primer/paint route for durability?   I have recently gotten a paint sprayer but am open to rolling if that’s preferable. I’ll attach my budget sprayer below for context.   Thanks so much, this is by far the best woodworking podcast.  -Dave Hello Huy, Guy, and Brian! You gentlemen, as well as Sean, have been a huge help and inspiration to my woodworking journey. Keep the great content coming! I recently picked up an older Bosch 1615 evs plunge router mounted to an old tabletop with an Incra Intelli fence. While I can find manuals online for both of these discontinued items, I'd like to get your input on how to best set up an older router with this fence. Since this particular router is in its own molded housing, I don't think a router lift is an option. What do you all recommend for setting this router up in a new table? I intend to likely build a stand-alone router table with a top made with melamine left over from a recent project, but I'm open to suggestions. Thanks, -Kurt Huy's Questions: Hi everyone,  Thank you for a great show. I've listened through the entire catalog twice, learning a lot.  In Episode #115 (and other episodes) you mention UV light turning walnut orange. I recently built a large dining room table out of walnut. I did not dye the table, even though I knew color change was possible. I have never used dye and the walnut was so stunning, I was afraid I would mess it up.  If my table turns orange, can it be sanded off? How deep does the UV "damage" go into the wood?  If I was to dye the walnut, could you please remind us what color dye you have used that works on walnut? How you have applied it to walnut, and when in the finishing process? hanks again for a great show and a great woodworking education.  Kevin Hello Gentleman,   Love the podcast. Thanks for all your hard work.  I am considering tackling a Entertainment unit for my bonus room; however I am struggling with material choice. The cabinet finish will be painted, do you suggest plywood or MDF? I plan on building some drawers with plywood boxes and MDF faces but I am concerned about the durability of the MDF when installing hinges if I use it for the carcass construction.  The overall length of this build is 16" long by 8' tall with drawers along the bottom open shelving on either side of that with the TV in the middle. Normally I am not so indecisive ; however this is such a large project and with the high cost of materials I want to start off on the right foot. Any guidance would be appreciated.  - Mike

Making Your Own Dominos, Painting Your Projects, Plywood or MDF? and MORE!

Brians Questions: Every time I make a jig I struggle to get the fence square. How do I do this properly. Is this a common problem amongst new woodworkers? Love the show guys keep it up! Johnny This is Ben and I’m 8 years old. I would like to make a pocket knife with my dad. What suggestions do you have for making one? Ben and Nathan Guys Questions: I recently found your podcast and have been binging it while in the shop. Guy, I was quite surprised to learn about your passion for 3D printing and various tinkering in his shop. I share the same passion for tinkering that extends beyond woodworking. In my shop I get almost as much satisfaction in discovering/creating a jig or tool to complete the job as I do in the actual finished product. My biggest “tool” build has been the ‘Mostly Printed CNC machine’, which is good enough for cutting various templates or basic v-carves. I can’t justify the price tag for an off the shelf machine to do that work when this one is good enough for me, at least for now. But I don’t think I could ever make something like a dowelmax, when I can buy a quality tool for relatively cheap. Apologies if this has been asked before. My question is about shop built tools and jigs vs. store bought. From your perspectives, with quality and cost in mind, what tools should be purchased off the shelf and what tools can be or maybe should be shop made? (Crosscut sleds, planer jointing sled, flattening jigs, clamping jigs, mobile bases, router tables…the list goes on and on). For reference I’m very much a hobbyist making stuff for the house or family and friends, while selling a piece here and there. So I do not work under any form of deadlines other than those imposed by my wife. Additionally, this is my creative outlet, I’m a gear design engineer the other 40 hours, this is my opportunity to make what I want to make. Keep up the great work! Caleb Gurd Gears &amp; Grain Woodcraft Hey guys. You have been kind enough to answer a few of my questions in the past so thought I would throw a couple more your way. I have two questions which fall into the category of finishing. Number one - I'll be building a coffee table out of walnut which is a mix of heartwood and sapwood. I would like to find a way to blend the color of the mixed wood together. If I use a walnut dye on the entire project will the color of the heartwood and sapwood blend together and provide a uniform looking finish? If dying the wood is the solution can you recommend a brand of dye? Should the dye be oil or water based given that I'll likely use an oil based clear coat. I have never used dye in the past so any tips will be helpful. Answered - Second question. Our cherry wood kitchen table, which measures 36"W x 48"L, needs refinishing. I believe the original finish is an oil based pre-catalyzed lacquer. I'll be refinishing just the table top which has several scratches and shallow dents measuring up to 1/16" deep. The legs are painted black so no need to match the color of the top with the legs. Can you recommend a method for removing the original finish? I don't own or have access to a drum sander. Also, can you recommend a durable oil-based finish for refinishing the table top? Is spraying the preferred method for such a large surface area? Or, will a wipe-on poly do the job? Thanks again for all your help and expertise. Jack Francis Geneva, IL Huys Questions: Hello fellas. Thanks for the enjoyable podcast, I've been listening for months but finally asking a question. Where do you look for inspiration when it comes to design for furniture pieces? Any particular magazines or books you like to reference when coming up with designs. Not necessarily looking for how to's , but more on design and style. Thanks again! A. Torres Kind sirs- Wonderful job etc. and I hope this finds you well. I posit this question knowing full well that I "overthink things" (according to Guy), even though I am "really intelligent" and have "design style" (according to Huy, your Tom Fan Club membership package is in the mail, including a life-size Tom cutout, suitable for posing with for social media photos.) I need a second desk for a backup office when my in-laws visit. I have a nice 2.5" thick ambrosia maple slab about the right size, and a couple of 4' long, 6" x 8" pine posts. My idea is to wedge-mortice the posts through the slab to create two 30" legs, and then mortice those into the 18" offcuts to make wide "feet". Think two upside down capital "T" going through the slab 3' apart. Would this construction method obviate the need to consider wood movement, since I only have one point of contact between the pieces? My understanding of wood movement is that it is the constraining of movement that can cause issues; in this case I can see the mortices getting 1/16" wider in the winter but if they're wedged, who gives a care? Or, should I hide the mortices and give them a little wiggle room to avoid splitting if the legs swell? Would pine stretching, crack maple? There I go over thinking things again. But thank you for humoring me. I await your answers with bated breath - Tom the Bomb Figura

Brians Questions: Every time I make a jig I struggle to get the fence square. How do I do this properly. Is this a common problem amongst new woodworkers? Love the show guys keep it up! Johnny This is Ben and I’m 8 years old. I would like to make a pocket knife with my dad. What suggestions do you have for making one? Ben and Nathan Guys Questions: I recently found your podcast and have been binging it while in the shop. Guy, I was quite surprised to learn about your passion for 3D printing and various tinkering in his shop. I share the same passion for tinkering that extends beyond woodworking. In my shop I get almost as much satisfaction in discovering/creating a jig or tool to complete the job as I do in the actual finished product. My biggest “tool” build has been the ‘Mostly Printed CNC machine’, which is good enough for cutting various templates or basic v-carves. I can’t justify the price tag for an off the shelf machine to do that work when this one is good enough for me, at least for now. But I don’t think I could ever make something like a dowelmax, when I can buy a quality tool for relatively cheap. Apologies if this has been asked before. My question is about shop built tools and jigs vs. store bought. From your perspectives, with quality and cost in mind, what tools should be purchased off the shelf and what tools can be or maybe should be shop made? (Crosscut sleds, planer jointing sled, flattening jigs, clamping jigs, mobile bases, router tables…the list goes on and on). For reference I’m very much a hobbyist making stuff for the house or family and friends, while selling a piece here and there. So I do not work under any form of deadlines other than those imposed by my wife. Additionally, this is my creative outlet, I’m a gear design engineer the other 40 hours, this is my opportunity to make what I want to make. Keep up the great work! Caleb Gurd Gears &amp; Grain Woodcraft Hey guys. You have been kind enough to answer a few of my questions in the past so thought I would throw a couple more your way. I have two questions which fall into the category of finishing. Number one - I'll be building a coffee table out of walnut which is a mix of heartwood and sapwood. I would like to find a way to blend the color of the mixed wood together. If I use a walnut dye on the entire project will the color of the heartwood and sapwood blend together and provide a uniform looking finish? If dying the wood is the solution can you recommend a brand of dye? Should the dye be oil or water based given that I'll likely use an oil based clear coat. I have never used dye in the past so any tips will be helpful. Answered - Second question. Our cherry wood kitchen table, which measures 36"W x 48"L, needs refinishing. I believe the original finish is an oil based pre-catalyzed lacquer. I'll be refinishing just the table top which has several scratches and shallow dents measuring up to 1/16" deep. The legs are painted black so no need to match the color of the top with the legs. Can you recommend a method for removing the original finish? I don't own or have access to a drum sander. Also, can you recommend a durable oil-based finish for refinishing the table top? Is spraying the preferred method for such a large surface area? Or, will a wipe-on poly do the job? Thanks again for all your help and expertise. Jack Francis Geneva, IL Huys Questions: Hello fellas. Thanks for the enjoyable podcast, I've been listening for months but finally asking a question. Where do you look for inspiration when it comes to design for furniture pieces? Any particular magazines or books you like to reference when coming up with designs. Not necessarily looking for how to's , but more on design and style. Thanks again! A. Torres Kind sirs- Wonderful job etc. and I hope this finds you well. I posit this question knowing full well that I "overthink things" (according to Guy), even though I am "really intelligent" and have "design style" (according to Huy, your Tom Fan Club membership package is in the mail, including a life-size Tom cutout, suitable for posing with for social media photos.) I need a second desk for a backup office when my in-laws visit. I have a nice 2.5" thick ambrosia maple slab about the right size, and a couple of 4' long, 6" x 8" pine posts. My idea is to wedge-mortice the posts through the slab to create two 30" legs, and then mortice those into the 18" offcuts to make wide "feet". Think two upside down capital "T" going through the slab 3' apart. Would this construction method obviate the need to consider wood movement, since I only have one point of contact between the pieces? My understanding of wood movement is that it is the constraining of movement that can cause issues; in this case I can see the mortices getting 1/16" wider in the winter but if they're wedged, who gives a care? Or, should I hide the mortices and give them a little wiggle room to avoid splitting if the legs swell? Would pine stretching, crack maple? There I go over thinking things again. But thank you for humoring me. I await your answers with bated breath - Tom the Bomb Figura

Shop Built Jigs, Woodworking With Children, Finding Inspiration and MORE!!

Brians Questions: Hi guys, I'm a hobbyist woodworker on the gold coast Australia. I have slowly acquired all the tools I feel are necessary to build those pieces that my children will one day inherit/sell in a yard sale 😜 I don't have a bandsaw and have gotten by with a jigsaw in most situations. My major issue is when I have thick lumbar (5/4 for example) and need only a thin board. It's wasteful and expensive to plane it down and I feel a bandsaw is required for a good quality resaw. Is this a good enough reason to purchase a bandsaw? Sam Kruger Hey guys, Thank you so much for the podcast and as others say in almost every question, I learn the most from your podcast than any other woodworking podcast I listen to. Being from Indianapolis, I have a woodworking buddy who has taken a lot of classes at Marc Adam’s School of Woodworking (not sure if Brian and Guy are familiar). He has tried to get me to join a class but it is quite an investment due to the cost and also other factors such as possibly a week off of work depending on the class you sign up for. While I would love to take a class due to being exposed to new technique’s and tools, I just don’t know if it’s worth the investment when Im just a hobbyist with limited budget and space for tools. Two questions: 1. Have any of you taken a woodworking class like this before? 2. Is it worth the investment for the class, or should I continue to build skills by online research and building my shop with tools? Thanks for the great podcast and being willing to take my question. Jason Guys Questions: Hey folks! First off, welcome aboard Brian. You have filled Sean's shoes without skipping a beat. And I particularly enjoy how you engage with extra followup questions too I was thinking in my head! So my question is about Guys favorite bug excrement - shellac. She treated me wrong and I need help from my bros. Ok it's more of a rant, so hang with me.  I've been a shellac lover for a while. She's never been fickle. Used her on a dozen projects. Always great results. Always a good time. Always easy. And I always use a rubber...you know...to be safe. (babum psshh)  This time and I sanded down a second hand veneer 3'x4' table and decided to give it a shellac finish. Using the big box store's version, I grabbed my favorite blonde, got her drunk with half alcohol, grabbed a trusty rubber, and went to town on the table.  Ok. Ok. Enough with the puns. For the life of me, I ALWAYS got streaks on the surface no matter what I did. I tried different cuts, different applicators (rubber, foam brush and paint brush). Sanding between coats. Not sanding. Working super fast, going slow. Light coats, heavy coats. Whatever. I even went to the Google and found an article from 2010 in Fine Woodworking that said dilute with 25% mineral oil and then later wipe with Naphtha once dry. BIG mistake. Won't get into it. Still bitter. Apparently though, it's hard to apply shellac on large surfaces?  So here I am asking the experts. Do I really need to break out my HVLP spray gun and section off my garage? Or am I doing something wrong? Have any tips? Paul Thanks for delivering this content. I’ve learned a lot and I think I’ve listened to every episode. My question is about which router table to purchase. I have an old Rockler—they’re cheapest model. Looking to upgrade and considering 3 models in particular: Woodpeckers, Incra, and JessEm https://jessem.com/products/ultimate-excel-ii-package I believe Guy has both the woodpeckers and the incra and would like to hear from all of you what you have and what you would recommend. Part 2 of my question is I would like to add dovetail joinery to my repertoire, and was considering the incra router table (with the super system LS17 fence) specifically because of its setup for doing that. Is that a good way to go or should I buy a stand alone dovetail jig and if so which one? The other things I use my router table for are raised panel cabinet doors, dados, and obviously edge treatment. I’m a hobbyist trying to make this a full time job and primarily build cabinets and cabinet based furniture at this point. Have also done a bed and some tables (dining, and smaller). Sorry to be so long winded, I very much appreciate your input. -Austin, AJ Squared Woodworks Huys Questions: Hey guys, really enjoy the podcast. I hear you were low on questions and I had a couple so I thought I would send them.  First question. I am looking to build a bed for me and my wife. How can I determine the best wood to make it from? Cost is much more a factor than how it looks. Another factor is we are heavyset people and I want to be sure it's not going to break while we are on it, sleeping or otherwise. ;P  Second question. I want to make the bed in the style that I have seen on my IG feed, with castle joints. My concern is, when you cut the notches, aren't you weakening that piece of wood? I assume you would want the notch on the top for the side rails where some of the weight would be carried. But in a joint like that, I have always wondered if that type of joint would weaken the piece with the notch taken out of the bottom half.  Thanks Gents! -Jacob Hi guys! Thanks for continuing to put on an informative podcast, always a pleasure to listen to.  I have a question about dovetail jigs. I make a good amount of furniture pieces with drawers and am looking to potentially get a dovetail jig for drawers. 99% of my drawers are made of 1/2” stock. I have no desire to handcut, time and accuracy are important. I’ve heard these jigs can be a pain to set up but I’d imagine once set up it might be worth it. Any recommendations on a particular jig? Thanks! Lindsey

Brians Questions: Hi guys, I'm a hobbyist woodworker on the gold coast Australia. I have slowly acquired all the tools I feel are necessary to build those pieces that my children will one day inherit/sell in a yard sale 😜 I don't have a bandsaw and have gotten by with a jigsaw in most situations. My major issue is when I have thick lumbar (5/4 for example) and need only a thin board. It's wasteful and expensive to plane it down and I feel a bandsaw is required for a good quality resaw. Is this a good enough reason to purchase a bandsaw? Sam Kruger Hey guys, Thank you so much for the podcast and as others say in almost every question, I learn the most from your podcast than any other woodworking podcast I listen to. Being from Indianapolis, I have a woodworking buddy who has taken a lot of classes at Marc Adam’s School of Woodworking (not sure if Brian and Guy are familiar). He has tried to get me to join a class but it is quite an investment due to the cost and also other factors such as possibly a week off of work depending on the class you sign up for. While I would love to take a class due to being exposed to new technique’s and tools, I just don’t know if it’s worth the investment when Im just a hobbyist with limited budget and space for tools. Two questions: 1. Have any of you taken a woodworking class like this before? 2. Is it worth the investment for the class, or should I continue to build skills by online research and building my shop with tools? Thanks for the great podcast and being willing to take my question. Jason Guys Questions: Hey folks! First off, welcome aboard Brian. You have filled Sean's shoes without skipping a beat. And I particularly enjoy how you engage with extra followup questions too I was thinking in my head! So my question is about Guys favorite bug excrement - shellac. She treated me wrong and I need help from my bros. Ok it's more of a rant, so hang with me.  I've been a shellac lover for a while. She's never been fickle. Used her on a dozen projects. Always great results. Always a good time. Always easy. And I always use a rubber...you know...to be safe. (babum psshh)  This time and I sanded down a second hand veneer 3'x4' table and decided to give it a shellac finish. Using the big box store's version, I grabbed my favorite blonde, got her drunk with half alcohol, grabbed a trusty rubber, and went to town on the table.  Ok. Ok. Enough with the puns. For the life of me, I ALWAYS got streaks on the surface no matter what I did. I tried different cuts, different applicators (rubber, foam brush and paint brush). Sanding between coats. Not sanding. Working super fast, going slow. Light coats, heavy coats. Whatever. I even went to the Google and found an article from 2010 in Fine Woodworking that said dilute with 25% mineral oil and then later wipe with Naphtha once dry. BIG mistake. Won't get into it. Still bitter. Apparently though, it's hard to apply shellac on large surfaces?  So here I am asking the experts. Do I really need to break out my HVLP spray gun and section off my garage? Or am I doing something wrong? Have any tips? Paul Thanks for delivering this content. I’ve learned a lot and I think I’ve listened to every episode. My question is about which router table to purchase. I have an old Rockler—they’re cheapest model. Looking to upgrade and considering 3 models in particular: Woodpeckers, Incra, and JessEm <a href="https://jessem.com/products/ultimate-excel-ii-package" rel="nofollow" target="_blank">https://jessem.com/products/ultimate-excel-ii-package</a> I believe Guy has both the woodpeckers and the incra and would like to hear from all of you what you have and what you would recommend. Part 2 of my question is I would like to add dovetail joinery to my repertoire, and was considering the incra router table (with the super system LS17 fence) specifically because of its setup for doing that. Is that a good way to go or should I buy a stand alone dovetail jig and if so which one? The other things I use my router table for are raised panel cabinet doors, dados, and obviously edge treatment. I’m a hobbyist trying to make this a full time job and primarily build cabinets and cabinet based furniture at this point. Have also done a bed and some tables (dining, and smaller). Sorry to be so long winded, I very much appreciate your input. -Austin, AJ Squared Woodworks Huys Questions: Hey guys, really enjoy the podcast. I hear you were low on questions and I had a couple so I thought I would send them.  First question. I am looking to build a bed for me and my wife. How can I determine the best wood to make it from? Cost is much more a factor than how it looks. Another factor is we are heavyset people and I want to be sure it's not going to break while we are on it, sleeping or otherwise. ;P  Second question. I want to make the bed in the style that I have seen on my IG feed, with castle joints. My concern is, when you cut the notches, aren't you weakening that piece of wood? I assume you would want the notch on the top for the side rails where some of the weight would be carried. But in a joint like that, I have always wondered if that type of joint would weaken the piece with the notch taken out of the bottom half.  Thanks Gents! -Jacob Hi guys! Thanks for continuing to put on an informative podcast, always a pleasure to listen to.  I have a question about dovetail jigs. I make a good amount of furniture pieces with drawers and am looking to potentially get a dovetail jig for drawers. 99% of my drawers are made of 1/2” stock. I have no desire to handcut, time and accuracy are important. I’ve heard these jigs can be a pain to set up but I’d imagine once set up it might be worth it. Any recommendations on a particular jig? Thanks! Lindsey

Woodworking Classes, Router Tables, Dovetailed Drawers and More!!

Brians Questions: Hi again guys, And thank you for contiuing to make THE BEST woodworking podcast. I have an 8" benchtop style crappy planer(jointer) thicknesser combo machine. The cheap ones you find in lots of colors. It has straight blades and quite short in and outfeed tables. I also have an Axminster AT330ST thicknesser, large lunchbox style, 330mm capacity with a spiral cutter head. I generally do my edge jointing on the table saw with a sled. First of all. When do you choose to skip plane instead face jointing the board first? And second: Would you do it differently with my setup. Thanks again, Gøran Eliassen Nomad Makes Love the podcast, I have a small unheated shop in Northern Canada. I've learned that during the winter months I need to bring in all my glues and finishes as they don't respond well to freezing. I also learned the hard way that my warm glue on frozen wood doesn't work either. My question is, how long should the glue set before I can return it to freezing conditions? I usually try for 24 hours but this can create long delays in projects and fills my house with glue up panels. Also is there a type of glue that would work best in freezing conditions. CA glue works fine, but isn't strong enough for panel glue ups or assembly. - Ben Thought this might be a fun question. If you aren't familiar with the phrase "the cobbler's children have no shoes," it often means that you are taking care of other's needs before your own. But it can also be used to mean something that everyone expects of you in your field/craft that you have never done. For example, I always hear that everyone's first project is a cutting board, but I was in the craft for years before I made one! And I've yet to cut a mortise and tenon! So, what haven't you made that everyone would think you had, or what skill do you not have that it would be assumed you do? Peter Downing @mr.downing.woodworking on Instagram Huy's Questions: Hey guys! I appreciate your podcast and always look forward on listening to the latest episodes! I am a hobby woodworker who has done some commission builds. As my hobby is turning into a side hustle more and more I am wondering at what point do I make it “official”. I live in the Nashville, TN area and there is a strong market for custom woodworking. Whilst I don’t “need” the money, the thought of fueling my hobby and having the extra cash seems viable. Have any of you became an LLC or setup a DBA? Are there benefits on doing so even if my business would stay relatively small? Again, love the podcast and thank you for your contribution to the community! God Bless! -Will Great podcast! I am looking for your opinions on a good set of brad point drill bits that won't break the bank. I've been using a set from Harbor Freight, and I would like to step up in quality. I'm a hobbyist who doesn't need the best, just decent quality. Any ideas? -Dan I think that my next tool purchase might be for a tracksaw-like guide for a circular saw or something similar. We sometimes run into situations where we need to rip a straight line. This would actually be more for ‘carpentry’ applications than fine ‘woodworking’. Things like ripping a long 2x6 or 2x8 at an angle, or rip a sheet of plywood in the field (so portability and reasonable durability would be important). Whatever we buy would be used by a lot of different guys and we’d keep it in our shared workshop. Most of the guys have Dewalt circular saws but several guys have other brands (Milwaukee, Ridgid, etc.). So the track would have to be adjustable for the bases of the various saws. I’ve spent zero time investigating this. Thought I’d start here. Any recommendations? - Mark

Brians Questions: Hi again guys, And thank you for contiuing to make THE BEST woodworking podcast. I have an 8" benchtop style crappy planer(jointer) thicknesser combo machine. The cheap ones you find in lots of colors. It has straight blades and quite short in and outfeed tables. I also have an Axminster AT330ST thicknesser, large lunchbox style, 330mm capacity with a spiral cutter head. I generally do my edge jointing on the table saw with a sled. First of all. When do you choose to skip plane instead face jointing the board first? And second: Would you do it differently with my setup. Thanks again, Gøran Eliassen Nomad Makes Love the podcast, I have a small unheated shop in Northern Canada. I've learned that during the winter months I need to bring in all my glues and finishes as they don't respond well to freezing. I also learned the hard way that my warm glue on frozen wood doesn't work either. My question is, how long should the glue set before I can return it to freezing conditions? I usually try for 24 hours but this can create long delays in projects and fills my house with glue up panels. Also is there a type of glue that would work best in freezing conditions. CA glue works fine, but isn't strong enough for panel glue ups or assembly. - Ben Thought this might be a fun question. If you aren't familiar with the phrase "the cobbler's children have no shoes," it often means that you are taking care of other's needs before your own. But it can also be used to mean something that everyone expects of you in your field/craft that you have never done. For example, I always hear that everyone's first project is a cutting board, but I was in the craft for years before I made one! And I've yet to cut a mortise and tenon! So, what haven't you made that everyone would think you had, or what skill do you not have that it would be assumed you do? Peter Downing @mr.downing.woodworking on Instagram Huy's Questions: Hey guys! I appreciate your podcast and always look forward on listening to the latest episodes! I am a hobby woodworker who has done some commission builds. As my hobby is turning into a side hustle more and more I am wondering at what point do I make it “official”. I live in the Nashville, TN area and there is a strong market for custom woodworking. Whilst I don’t “need” the money, the thought of fueling my hobby and having the extra cash seems viable. Have any of you became an LLC or setup a DBA? Are there benefits on doing so even if my business would stay relatively small? Again, love the podcast and thank you for your contribution to the community! God Bless! -Will Great podcast! I am looking for your opinions on a good set of brad point drill bits that won't break the bank. I've been using a set from Harbor Freight, and I would like to step up in quality. I'm a hobbyist who doesn't need the best, just decent quality. Any ideas? -Dan I think that my next tool purchase might be for a tracksaw-like guide for a circular saw or something similar. We sometimes run into situations where we need to rip a straight line. This would actually be more for ‘carpentry’ applications than fine ‘woodworking’. Things like ripping a long 2x6 or 2x8 at an angle, or rip a sheet of plywood in the field (so portability and reasonable durability would be important). Whatever we buy would be used by a lot of different guys and we’d keep it in our shared workshop. Most of the guys have Dewalt circular saws but several guys have other brands (Milwaukee, Ridgid, etc.). So the track would have to be adjustable for the bases of the various saws. I’ve spent zero time investigating this. Thought I’d start here. Any recommendations? - Mark

Great First Projects, Hobby As A Side Hustle And Where Is Guy?

Brians Questions: I hear a lot of talk on forums and social media about buying smaller tools to make more room in your shop. I can see how something like a 52 inch rip fence will take up more room but in my little pea brain it takes as much room to plane and joint a 4 foot board on a 72 inch bed jointer and a 15 inch planer and it does a 46 inch bed jointer and a lunch box planer. Am I wrong? Should I take this into consideration when buying tools? I'm fortunate to have a 1000 sqft shop so space isn't necessarily at a premium but I'll also be shop building large built in closets and wine rooms and such so it may get tighter than I think. Thanks for all the info and keep it up. Michael I know how to sand through the grits. And I know why to sand through the grits. But how long (in general) should you stay at each grit? Obviously higher grits are easy. I usually stay there until any major imperfections are smoothed out. But as I progress, I’m always thinking I should stay there for one more round. Especially at my final grit. Normally I just keep going until the piece “feels” nice and smooth and flat. So far that’s worked for me. I’m sure I’m overthinking it, but figured I’d ask the experts what they do. I’m using an Orbital sander by the way. Sorry for the long winded question, you obviously don’t have to read all that. I ramble haha. Thanks so much. Mick at Broken Levee Woodworks Guys Questions: Hey guys and Guy. I’m building a dining table for a friend out of walnut and quarter sawn WO and am starting to think about applying finish. I’m wondering about applying a couple of coats of shellac to deepen the grain and following up with water based poly for the top coat(s). After hearing Guy tout the water based conversion varnish, I’m considering the General Finishes product that has the catalyst you have to mix in. Is that what you use Guy? As far as the shellac, is that a bad idea? I don’t feel confident getting an even coat, especially on the top, using a hand application so I would like to spray. Does that sound feasible? I also don’t want to change the color, jus deepen the grain so what flavor of shellac and cut should I use? Enjoy you guys a lot. My favorite woodworking podcast. Tom Bigmuddy Woodworks Hey fellas, I have a question about the Domino 500 and 700. What rule(s) of thumb do you use for when to use the 700 instead of the 500 when it's not an obvious situation? Other than the 3rd's of the stock thickness. Thanks for all of your different points of view on how to tackle situations we find ourselves in. Matt in AL Huy's Questions: Where do you find the most objective tool reviews? Have a great day Chuck Alabama ww said he has done half blind dovetails where you cut thru dovetails and add an 1/8 piece on the front. Could you expand on your process for doing this specifically adding the false front and getting it flush to sub front sides. Thank you, Schatz

Brians Questions: I hear a lot of talk on forums and social media about buying smaller tools to make more room in your shop. I can see how something like a 52 inch rip fence will take up more room but in my little pea brain it takes as much room to plane and joint a 4 foot board on a 72 inch bed jointer and a 15 inch planer and it does a 46 inch bed jointer and a lunch box planer. Am I wrong? Should I take this into consideration when buying tools? I'm fortunate to have a 1000 sqft shop so space isn't necessarily at a premium but I'll also be shop building large built in closets and wine rooms and such so it may get tighter than I think. Thanks for all the info and keep it up. Michael I know how to sand through the grits. And I know why to sand through the grits. But how long (in general) should you stay at each grit? Obviously higher grits are easy. I usually stay there until any major imperfections are smoothed out. But as I progress, I’m always thinking I should stay there for one more round. Especially at my final grit. Normally I just keep going until the piece “feels” nice and smooth and flat. So far that’s worked for me. I’m sure I’m overthinking it, but figured I’d ask the experts what they do. I’m using an Orbital sander by the way. Sorry for the long winded question, you obviously don’t have to read all that. I ramble haha. Thanks so much. Mick at Broken Levee Woodworks Guys Questions: Hey guys and Guy. I’m building a dining table for a friend out of walnut and quarter sawn WO and am starting to think about applying finish. I’m wondering about applying a couple of coats of shellac to deepen the grain and following up with water based poly for the top coat(s). After hearing Guy tout the water based conversion varnish, I’m considering the General Finishes product that has the catalyst you have to mix in. Is that what you use Guy? As far as the shellac, is that a bad idea? I don’t feel confident getting an even coat, especially on the top, using a hand application so I would like to spray. Does that sound feasible? I also don’t want to change the color, jus deepen the grain so what flavor of shellac and cut should I use? Enjoy you guys a lot. My favorite woodworking podcast. Tom Bigmuddy Woodworks Hey fellas, I have a question about the Domino 500 and 700. What rule(s) of thumb do you use for when to use the 700 instead of the 500 when it's not an obvious situation? Other than the 3rd's of the stock thickness. Thanks for all of your different points of view on how to tackle situations we find ourselves in. Matt in AL Huy's Questions: Where do you find the most objective tool reviews? Have a great day Chuck Alabama ww said he has done half blind dovetails where you cut thru dovetails and add an 1/8 piece on the front. Could you expand on your process for doing this specifically adding the false front and getting it flush to sub front sides. Thank you, Schatz

Big Tools In A Small Shop, Shellac Finish, Tool Reviews and MORE!

Guy's Questions:  Hi all: First, I love the podcast. I listen to several others as well. This is by far the best, the Premier podcast on woodworking. Your focus on the questions is outstanding. I know that you repeat yourselves often but it it is so helpful to those of us that are trying to learn the craft. I learn something every time I listen. Thanks! My question has to do with spraying a finish. I just bought my first HVLP sprayer. I’ve watched many of the YouTube videos on the basic process with regard to how to tune the gun and the process and motion of applying the finish. Many of the finishes today, especially water based finishes, dry very quickly. So what do you do between coats? Do you always breakdown and clean the gun and all of the other components? Is there some tricks that you use to keep the gun clean and ready for the next coat, without breaking it all down and starting a new? Thanks again, Joe Hey guys. I've been watching all the New Yankee Workshop episodes as they're being released on YouTube lately. Interesting to see how Norm did things back then, including how some of his techniques evolved over the years. One thing he almost always does is pin his tenons with dowels. I don't see this much today unless it's a draw bore, which I don't see Norm do ever. (This pinning is almost always followed up with one of Norm's favorite phrases, "That's never coming apart!") I guess the question is, should we be pinning tenons? Only in specific circumstances? Only if a draw bore? Peter Infinity tools pro router table package with 3 1/4 Triton or a Grizzly G1035 shaper that can still run 1/2" router bits. Always lots of talk about router tables but never anything about smaller shapers. I found this podcast a while ago and have made my way through all the episodes, I really appreciate all the great content, keep it up. Mike Huy's Questions: Hey guys! I know you asked for more questions so I am going to try to help. I have a question about applying Odies Oil with a buffer. I’ve been using Odies because it’s too much work making a spray booth for spray finishing in my woodshop. I have applied Odies by hand with success but it’s a lot of buffing work. Gem buffers are pretty expensive, has anyone tried putting a hook and loop pad on a car buffer and just put a non woven pad on it? Big Cedar table Co. Can you give any recommendations of hardwoods you enjoy to make furniture with? Alot of the furniture I've built in my house has been made from Walnut, White oak and cherry and am looking for something new. I'm looking to build some new furniture for my basement (tv stand, coffee table, maybe a dry bar to match species) but am looking for something new to use other than those stated above. Thanks for all you do. Paul Genereux at Twin Lake Woodshop Hey, guys. Love the show. Appreciate the fact that you answer questions and although there is a little banter between the three of you, it doesn't dominate the podcast as other shows do. I want to attend a "convention" for woodworkers and am curious if you have suggestions on what would be a good convention for woodworkers to attend. Thanks in advance! Greg

Guy's Questions:  Hi all: First, I love the podcast. I listen to several others as well. This is by far the best, the Premier podcast on woodworking. Your focus on the questions is outstanding. I know that you repeat yourselves often but it it is so helpful to those of us that are trying to learn the craft. I learn something every time I listen. Thanks! My question has to do with spraying a finish. I just bought my first HVLP sprayer. I’ve watched many of the YouTube videos on the basic process with regard to how to tune the gun and the process and motion of applying the finish. Many of the finishes today, especially water based finishes, dry very quickly. So what do you do between coats? Do you always breakdown and clean the gun and all of the other components? Is there some tricks that you use to keep the gun clean and ready for the next coat, without breaking it all down and starting a new? Thanks again, Joe Hey guys. I've been watching all the New Yankee Workshop episodes as they're being released on YouTube lately. Interesting to see how Norm did things back then, including how some of his techniques evolved over the years. One thing he almost always does is pin his tenons with dowels. I don't see this much today unless it's a draw bore, which I don't see Norm do ever. (This pinning is almost always followed up with one of Norm's favorite phrases, "That's never coming apart!") I guess the question is, should we be pinning tenons? Only in specific circumstances? Only if a draw bore? Peter Infinity tools pro router table package with 3 1/4 Triton or a Grizzly G1035 shaper that can still run 1/2" router bits. Always lots of talk about router tables but never anything about smaller shapers. I found this podcast a while ago and have made my way through all the episodes, I really appreciate all the great content, keep it up. Mike Huy's Questions: Hey guys! I know you asked for more questions so I am going to try to help. I have a question about applying Odies Oil with a buffer. I’ve been using Odies because it’s too much work making a spray booth for spray finishing in my woodshop. I have applied Odies by hand with success but it’s a lot of buffing work. Gem buffers are pretty expensive, has anyone tried putting a hook and loop pad on a car buffer and just put a non woven pad on it? Big Cedar table Co. Can you give any recommendations of hardwoods you enjoy to make furniture with? Alot of the furniture I've built in my house has been made from Walnut, White oak and cherry and am looking for something new. I'm looking to build some new furniture for my basement (tv stand, coffee table, maybe a dry bar to match species) but am looking for something new to use other than those stated above. Thanks for all you do. Paul Genereux at Twin Lake Woodshop Hey, guys. Love the show. Appreciate the fact that you answer questions and although there is a little banter between the three of you, it doesn't dominate the podcast as other shows do. I want to attend a "convention" for woodworkers and am curious if you have suggestions on what would be a good convention for woodworkers to attend. Thanks in advance! Greg

Best HVLP Finish, Norm Abrams, Conventions/Shows and MORE!

Brians Questions: I inherited my dad’s woodworking tools almost 20 years ago. I’ve upgraded several tools over the years. Most significantly, I replaced his Craftsman contractor table saw with a Sawstop PCS 175 5 years ago. I bought it for the safety mechanism, but I’ve really enjoyed using a cabinet saw. While I consistently use the riving knife, I have seldom used the blade guard cover. I like being able to clearly see the blade meeting the wood. Question/topic: how do you balance safety and convenience in your woodshop? Thank you. Chuck I inherited my dad’s woodworking tools almost 20 years ago. I’ve upgraded several tools over the years. Most significantly, I replaced his Craftsman contractor table saw with a Sawstop PCS 175 5 years ago. I bought it for the safety mechanism, but I’ve really enjoyed using a cabinet saw. While I consistently use the riving knife, I have seldom used the blade guard cover. I like being able to clearly see the blade meeting the wood. Question/topic: how do you balance safety and convenience in your woodshop? Thank you. Chuck Guys Questions: Hey Gentleman (and Guy), Thanks for the great podcast. I'm lucky enough to be able to pester Guy directly with my questions, and he's gracious enough to answer them. Do you have any "Dream Projects"? Something that you have always wanted to build, but just haven't had the time or resources to do it? Think you will ever get to it? Thanks again for sharing all your knowledge, look forward to hearing your answers -Theo I've heard at least one of you maybe Guy in the beginning say there were quite a few years that went by without a table saw in the shop. I very recently took a big step and got a rikon 14" deluxe band saw as well as the Makita track saw. My table saw is a deplorable early 90's job site Makita. really bad fence zero dust collection tiny arbor. It works but guy has maybe once compared a Cadillac vs a pinto and I own the table saw pinto that got into a wreck and then blew up and Given my two recent big purchases what would you say my big limitations are by not having a serious table saw? Can I get by wanting to make boxes? Can I get by without another big purchase such as a table saw? What do you guys see as limitations given my recent purchases? Jim Huys Questions: Hey all, another question. I'm wanting to get into spraying finish, I've seen the option and have heard decent things about the harbor frieght paint sprayer with regulator which is like 30$. I'm wondering what you guys think of it or if any of you have experiences with it? I have a 30 gal air compressor and I'm only looking at small pieces up to a night stand size, so I think that should suffice? I would love to get a 4 stage but that is very much out of the question price wise. Also I'm looking to mostly spray Shelac and conversion varnish. How easy is it to clean? Guy makes it sound extremely easy so I'm curious if Guy or Hue have any videos about cleaning? Sorry I know it's long winded but thank you guys for what you do! Look forward to hearing the answers. Blairswoodshop I have a question about "refinishing" a shelf. I built a floating shelf out of walnut about 2 years ago and did miter-folded edges all the way around. It's a small shelf, only 32" long, 3" tall face, and 6" deep. My wife would like the same size shelf in white oak. Could i sand back the finish and veneer it in white oak? Or do I need to start from scratch and build a new shelf? Brian

Brians Questions: I inherited my dad’s woodworking tools almost 20 years ago. I’ve upgraded several tools over the years. Most significantly, I replaced his Craftsman contractor table saw with a Sawstop PCS 175 5 years ago. I bought it for the safety mechanism, but I’ve really enjoyed using a cabinet saw. While I consistently use the riving knife, I have seldom used the blade guard cover. I like being able to clearly see the blade meeting the wood. Question/topic: how do you balance safety and convenience in your woodshop? Thank you. Chuck I inherited my dad’s woodworking tools almost 20 years ago. I’ve upgraded several tools over the years. Most significantly, I replaced his Craftsman contractor table saw with a Sawstop PCS 175 5 years ago. I bought it for the safety mechanism, but I’ve really enjoyed using a cabinet saw. While I consistently use the riving knife, I have seldom used the blade guard cover. I like being able to clearly see the blade meeting the wood. Question/topic: how do you balance safety and convenience in your woodshop? Thank you. Chuck Guys Questions: Hey Gentleman (and Guy), Thanks for the great podcast. I'm lucky enough to be able to pester Guy directly with my questions, and he's gracious enough to answer them. Do you have any "Dream Projects"? Something that you have always wanted to build, but just haven't had the time or resources to do it? Think you will ever get to it? Thanks again for sharing all your knowledge, look forward to hearing your answers -Theo I've heard at least one of you maybe Guy in the beginning say there were quite a few years that went by without a table saw in the shop. I very recently took a big step and got a rikon 14" deluxe band saw as well as the Makita track saw. My table saw is a deplorable early 90's job site Makita. really bad fence zero dust collection tiny arbor. It works but guy has maybe once compared a Cadillac vs a pinto and I own the table saw pinto that got into a wreck and then blew up and Given my two recent big purchases what would you say my big limitations are by not having a serious table saw? Can I get by wanting to make boxes? Can I get by without another big purchase such as a table saw? What do you guys see as limitations given my recent purchases? Jim Huys Questions: Hey all, another question. I'm wanting to get into spraying finish, I've seen the option and have heard decent things about the harbor frieght paint sprayer with regulator which is like 30$. I'm wondering what you guys think of it or if any of you have experiences with it? I have a 30 gal air compressor and I'm only looking at small pieces up to a night stand size, so I think that should suffice? I would love to get a 4 stage but that is very much out of the question price wise. Also I'm looking to mostly spray Shelac and conversion varnish. How easy is it to clean? Guy makes it sound extremely easy so I'm curious if Guy or Hue have any videos about cleaning? Sorry I know it's long winded but thank you guys for what you do! Look forward to hearing the answers. Blairswoodshop I have a question about "refinishing" a shelf. I built a floating shelf out of walnut about 2 years ago and did miter-folded edges all the way around. It's a small shelf, only 32" long, 3" tall face, and 6" deep. My wife would like the same size shelf in white oak. Could i sand back the finish and veneer it in white oak? Or do I need to start from scratch and build a new shelf? Brian

Table Saw Safety, Dream Projects, Cheap Sprayers and MORE!

Brians Questions: Hey guys, Got another one for ya. I have never used real hardwood for a project. Everything I have done so far has been with random scraps, pine or plywood. I was wondering what you guys would suggest as a good first project using hardwood. I do have a small variety pack of 3 species I picked up from woodcraft a while back that was on sale. 3 small boards that are essentially 2' 1x4's. Couldn't tell you what species they are at this point. I had thought about starting out by making a simple wood mallet using these. As a companion question. What general advice would you give someone just starting out. I don't have a planer or joiner so where should I get my hardwood? Do typical wood suppliers have an option to purchase already dimensioned lumber? I know a big box store is always an option. What species would you recommend getting started with? Any other helpful tips for this rookie? Thanks again, Jon Guys Questions: Hello gents, My wife creates some really detailed pyrography on offcuts from my woodworking projects. Usually I give them a light coating of linseed oil or tung oil but We’ve found over time, and in particular when in direct sunlight, that the burnt image fades quite a lot. Any ideas on a finish that would help prevent or reduce this fading? Thanks Adam (listener from the UK) Hey all this is Mason with Blairswoodshop again. I've been thinking of more questions to ask and I have a couple. I'll start with this one and send the others later. I've been seeing a lot of advertising from finewoodworking magazine about some online courses. I'm actually quite interested. I live in a rual area of Missouri and before that I was in a rural area of Southern California. So any kind of in-person class is always a 2-3 hour drive away. I know there is a lot of experience lost with the lack of hands on and in person instruction, but do you all still think there is something to be gained through online live instruction? Most of my experience is through hours of research, reading, listening to this podcast, YouTube, and hands on experience. I feel I could learn some processes faster even through a camera, where my questions can be answered directly at that moment. Sorry about the long winded question, but I am curious of what you guys think? Huys Questions: Huy, Guy, Newbie Brian - First off let me apologize for taking a month off from my regular queries. I had to go ahead and dodge a process server after my 7 year old made me get my wife a toilet seat heater for Christmas. Second, Happy New Year to you and yours. May your 2023 be filled with etcetera. Third, I got a hot one for you. Had a 30" diameter beech tree taken down out of my deck (it was growing through it), and saved the bottom 10'. Borrowed my buddy's chainsaw and Alaskan mill and slabbed it up into 8/4. Here is my conundrum. I am 95% sure I will use all but two slabs as milled lumber to make a big dresser. Would you, if you were in my size 13's, mill the lumber to rough size green/now, and then air dry it, or dry it as stacked slabs and then mill it? I can see advantages and disadvantages to both approaches, I'm leaning towards leaving it as slabs only because beech is notorious for twisting as it dries, and I feel like less mass moves easier. But then I consider that if it has innate tension, it's going to move when I mill it, no matter what. I have a whole bunch of other questions but I like a nice lead-in to warm up the audience, so I'll send them individually. You guys breaking trying to break up a multi-parter would just throw off my flow. Love you miss you. Tom @figurawoodwork I use Odie’s oil. I don’t like it for furniture at all though. I think it looks nice, but I question the durability. That said, I do use it on pens that I sell. You do not get a high shine, but it does leave a nice, natural looking finish with a moderate shine. Plus it applies super easily and seems durable enough for my pens. I was wondering if you guys had a take on hard wax oils for wood turnings. We don’t talk about lathe work a lot. Dillon

Brians Questions: Hey guys, Got another one for ya. I have never used real hardwood for a project. Everything I have done so far has been with random scraps, pine or plywood. I was wondering what you guys would suggest as a good first project using hardwood. I do have a small variety pack of 3 species I picked up from woodcraft a while back that was on sale. 3 small boards that are essentially 2' 1x4's. Couldn't tell you what species they are at this point. I had thought about starting out by making a simple wood mallet using these. As a companion question. What general advice would you give someone just starting out. I don't have a planer or joiner so where should I get my hardwood? Do typical wood suppliers have an option to purchase already dimensioned lumber? I know a big box store is always an option. What species would you recommend getting started with? Any other helpful tips for this rookie? Thanks again, Jon Guys Questions: Hello gents, My wife creates some really detailed pyrography on offcuts from my woodworking projects. Usually I give them a light coating of linseed oil or tung oil but We’ve found over time, and in particular when in direct sunlight, that the burnt image fades quite a lot. Any ideas on a finish that would help prevent or reduce this fading? Thanks Adam (listener from the UK) Hey all this is Mason with Blairswoodshop again. I've been thinking of more questions to ask and I have a couple. I'll start with this one and send the others later. I've been seeing a lot of advertising from finewoodworking magazine about some online courses. I'm actually quite interested. I live in a rual area of Missouri and before that I was in a rural area of Southern California. So any kind of in-person class is always a 2-3 hour drive away. I know there is a lot of experience lost with the lack of hands on and in person instruction, but do you all still think there is something to be gained through online live instruction? Most of my experience is through hours of research, reading, listening to this podcast, YouTube, and hands on experience. I feel I could learn some processes faster even through a camera, where my questions can be answered directly at that moment. Sorry about the long winded question, but I am curious of what you guys think? Huys Questions: Huy, Guy, Newbie Brian - First off let me apologize for taking a month off from my regular queries. I had to go ahead and dodge a process server after my 7 year old made me get my wife a toilet seat heater for Christmas. Second, Happy New Year to you and yours. May your 2023 be filled with etcetera. Third, I got a hot one for you. Had a 30" diameter beech tree taken down out of my deck (it was growing through it), and saved the bottom 10'. Borrowed my buddy's chainsaw and Alaskan mill and slabbed it up into 8/4. Here is my conundrum. I am 95% sure I will use all but two slabs as milled lumber to make a big dresser. Would you, if you were in my size 13's, mill the lumber to rough size green/now, and then air dry it, or dry it as stacked slabs and then mill it? I can see advantages and disadvantages to both approaches, I'm leaning towards leaving it as slabs only because beech is notorious for twisting as it dries, and I feel like less mass moves easier. But then I consider that if it has innate tension, it's going to move when I mill it, no matter what. I have a whole bunch of other questions but I like a nice lead-in to warm up the audience, so I'll send them individually. You guys breaking trying to break up a multi-parter would just throw off my flow. Love you miss you. Tom @figurawoodwork I use Odie’s oil. I don’t like it for furniture at all though. I think it looks nice, but I question the durability. That said, I do use it on pens that I sell. You do not get a high shine, but it does leave a nice, natural looking finish with a moderate shine. Plus it applies super easily and seems durable enough for my pens. I was wondering if you guys had a take on hard wax oils for wood turnings. We don’t talk about lathe work a lot. Dillon

Scrap Wood Projects, Online Classes, Drying Lumber and MORE!!

Brians Questions: Does a combination square needs to be a Starrett ($$$$) or we clan go with cheaper brands. Kind regards from São Paulo - Brazil. Hey guys, quick question for you. I have an old grizzly 20" planer and I want to resaw some wood on my bandsaw down to 1/2" and 1/4" pieces. The bandsaw is from 1943 and doesn't leave the best finish. The minimum thickness on the planer is 1/2" but I see the piece do some shimmying when I put stock that thin through there. What's the best way to finish planing the stock and finishing it off without access to a drum sander? Any tips would be much appreciated. Love the show and keep up the good work! JARED Guy's Questions: Hey guys. I have been wanting to ask this for a while now. I have been asked by my wife to build dresser for our bedroom. This would be my first time building drawers. I have the cabinet built and the drawer boxes built. But when I put the slides on the drawers just don’t glide like I would think they would. I mean some of them do. I am just not sure what I am doing wrong. I have checked all my spacing for the openings. Could it be my boxes are not square? What is the best way to get them square? Nick. I've been listening for a few years now, and have learned a lot. My most pressing question is about finishing. Recently l've built a couple kitchen tables that I really wanted to be special and put a lot of time into them. I thought everything turned out great, but at the final step, topcoating, I got a lot of streaking - more so than I've gotten before (although this is a bigger surface area project than I've ever done). I stained it, then used AquaCoat water-based grain filler (which left a few minor streaks across the grain that I couldn't sand out, but I can live with that), and then 3 coats of ArmRSeal satin. After the 3rd coat I had a dull sheen in one spot and so gave it a 4th coat of satin, pretty thick this time, and the sheen streaking got worse. Am assuming that I need to sand it down (and hopefully not get down into the stain) and start again. Someone suggested gloss or semi-gloss ArmRSeal and then a final coat with satin. Is there an easier solution - buff it out?? Mark Schmidt Huy's Questions:  Hello gentlemen. I stumbled across your podcast a few months ago and have been enjoying it ever since. I apologize I have not spent a lot of time going back through older episodes, so this question may have come up already. I’ve been woodworking as a hobby for several years now and enjoy it as my creative outlet. I prefer making smaller pieces as opposed to big furniture but have dabbled with both as gifts and favors to friends. In 2023 I’d like to start turning this into a small business. I enjoy my day job, so this would be more of a side hustle to make enough money to buy more wood and tools (and maybe whiskey 😉). Do you have any tips or tricks for getting started selling projects? Facebook marketplace seems like a dead zone and Etsy seems saturated. Thanks, and I appreciate any advice you have on this subject. Nick Hellman I am slowly trying to turn my tiny shed into a shop. It is coming along but is not climate controlled. I was recently glueing up some thin strips of wood for an accent on a holiday gift. I live in Oregon, about an hour east of Portland. It doesn’t get super cold here usually, but that week was a bit colder than usual. Anyway, when I went to trim up the strips they came apart where they were glued up. The glue didn’t bond at all. There was just white remnants of dry glue. After asking a friend who is a professional woodworker and reading the label I learned that you can’t use wood glue below 46°. The bottle says not to let it freeze. My friend told me once the bottle freezes it is not good anymore. I bought a new bottle and am keeping it inside the house and doing glue ups inside until the spring. Is this true that once the bottle freezes it’s no good? Any advice for working in the winter in an unheated shop? Should I worry about the wood moving when I bring it inside? Any other products I should worry about in cold temps? Thanks. Happy New Year! Jon Moch

Brians Questions: Does a combination square needs to be a Starrett ($$$$) or we clan go with cheaper brands. Kind regards from São Paulo - Brazil. Hey guys, quick question for you. I have an old grizzly 20" planer and I want to resaw some wood on my bandsaw down to 1/2" and 1/4" pieces. The bandsaw is from 1943 and doesn't leave the best finish. The minimum thickness on the planer is 1/2" but I see the piece do some shimmying when I put stock that thin through there. What's the best way to finish planing the stock and finishing it off without access to a drum sander? Any tips would be much appreciated. Love the show and keep up the good work! JARED Guy's Questions: Hey guys. I have been wanting to ask this for a while now. I have been asked by my wife to build dresser for our bedroom. This would be my first time building drawers. I have the cabinet built and the drawer boxes built. But when I put the slides on the drawers just don’t glide like I would think they would. I mean some of them do. I am just not sure what I am doing wrong. I have checked all my spacing for the openings. Could it be my boxes are not square? What is the best way to get them square? Nick. I've been listening for a few years now, and have learned a lot. My most pressing question is about finishing. Recently l've built a couple kitchen tables that I really wanted to be special and put a lot of time into them. I thought everything turned out great, but at the final step, topcoating, I got a lot of streaking - more so than I've gotten before (although this is a bigger surface area project than I've ever done). I stained it, then used AquaCoat water-based grain filler (which left a few minor streaks across the grain that I couldn't sand out, but I can live with that), and then 3 coats of ArmRSeal satin. After the 3rd coat I had a dull sheen in one spot and so gave it a 4th coat of satin, pretty thick this time, and the sheen streaking got worse. Am assuming that I need to sand it down (and hopefully not get down into the stain) and start again. Someone suggested gloss or semi-gloss ArmRSeal and then a final coat with satin. Is there an easier solution - buff it out?? Mark Schmidt Huy's Questions:  Hello gentlemen. I stumbled across your podcast a few months ago and have been enjoying it ever since. I apologize I have not spent a lot of time going back through older episodes, so this question may have come up already. I’ve been woodworking as a hobby for several years now and enjoy it as my creative outlet. I prefer making smaller pieces as opposed to big furniture but have dabbled with both as gifts and favors to friends. In 2023 I’d like to start turning this into a small business. I enjoy my day job, so this would be more of a side hustle to make enough money to buy more wood and tools (and maybe whiskey 😉). Do you have any tips or tricks for getting started selling projects? Facebook marketplace seems like a dead zone and Etsy seems saturated. Thanks, and I appreciate any advice you have on this subject. Nick Hellman I am slowly trying to turn my tiny shed into a shop. It is coming along but is not climate controlled. I was recently glueing up some thin strips of wood for an accent on a holiday gift. I live in Oregon, about an hour east of Portland. It doesn’t get super cold here usually, but that week was a bit colder than usual. Anyway, when I went to trim up the strips they came apart where they were glued up. The glue didn’t bond at all. There was just white remnants of dry glue. After asking a friend who is a professional woodworker and reading the label I learned that you can’t use wood glue below 46°. The bottle says not to let it freeze. My friend told me once the bottle freezes it is not good anymore. I bought a new bottle and am keeping it inside the house and doing glue ups inside until the spring. Is this true that once the bottle freezes it’s no good? Any advice for working in the winter in an unheated shop? Should I worry about the wood moving when I bring it inside? Any other products I should worry about in cold temps? Thanks. Happy New Year! Jon Moch

Off Brand Tools, Perfect Drawer Slides, Selling Your Work For $$$, And MORE!

Bi-Weekly Podcast Focused on the Craft of Woodworking

Guy's Questions: Good afternoon Gentlemen, Thank you for your podcast, I really appreciate it, and you fellows. Long story short, I am a re-engaging woodworker after taking a 20 year hiatus. Due to life requirements and work travel frequency, I was unable to keep up my hobby. I now have the time (and hopefully will NEVER have to fly somewhere for work again) to start anew. Things have changed quite a bit in past couple decades, and so have my interests in terms of wood working. Over my hiatus, I sold some of my equipment in hopes the machines would be used instead of sitting idle and it is time to re-equip my shop needs with eliminated tools and new needs. My tool requirements are also much different today, then they were 20 years ago. One requirement I now have is a drum sander. I don't have the desire to rotate any work (key point), and want to acquire a machine that fits my specific needs, thus an 18" capability is perfect for what my new woodworking interests require. I also refuse to take any advice from boob tube woodworkers recommendations, as it seems that 90% of the creators I find may have started out providing woodworking content, but they mostly all just become prejudiced tool reviewers who conflict each other based on who is giving them free tools or paying them. I have lost a lot of respect for some woodworkers on YouTube who used to be considered by me as inspirations in their early YouTube careers, no longer. With that said, I have trimmed my interest list down to a Jet 1836 and Supermax 19-38. I imagine some or all of you have had experience with both, and would like your feedback. I am not currently considering models with moving/height adjustable belts such as the shop fox/grizzly, however if you have anything to add on those, it would be nice to hear. Glad you have a new host, it seems like he may be a great fit for the podcast. Well wishes to all of you, and Guy, I hope your health is well. Kurtis Van Kampen You fellas have filled my head with hours and hours of information. You’re truly the best Podcast I’ve found. So before Guy’s head begins to swell, on with the question. I’ve started watching Nee Yankee workshop again now they I actually have a 520 sqft shop to work out in. In the first season Norm used what he called a panel cutting jig for the table saw. The fence of the jig was located on the blade side rather than the operator side like the modern crosscut sled. This jig is dead simple being made of only three boards. I had big plans to make a modern crosscut sled (not the aircraft carrier) with all the bells and whistles. Now I’m completely rethinking my next table saw jig. Since Guy (like myself) is the only one of you old enough to remember the first episode, this should probably be HIS question. Keep up the great work fellows. I appreciate what each of you bring to the table. -Bryan   Huy's Questions: I’d first like to say that I listen to a bunch of other woodworking podcasts as well, but of all of them, yours has the lowest level of useless off-topic banter. Keep up the good work. I have a question about the usage of my shop air cleaner. It’s a Jet AFS-1000B, and my ceiling is only 7’6”, so can’t hang it from there. So I have it on a roll-around cart. My shop is 13’ x 17’. I don’t have a central dust collection system, but for the following tools I hook up my shop vac to the tool: table saw, planer, drum sander, router table and random orbit sander. I also have a circular saw, a handheld router, a jigsaw, a drill press, a belt sander and a palm sander. My question is, for which tools should I be turning on the air cleaner, and on which setting? (it has low, medium and high settings) And how long should I keep it on for after the tool has been turned off? Thanks. Steve My perception is that the people who seem to get hurt the most are woodworking professionals who become too comfortable/familiar with machines. Is that a fair assessment? [I am a hobbyist woodworker.] FYI, on 3 I am just asking for a comment on my observation. Have a great day Chuck   Brians Questions: First, love the podcast and thank you! Question: I’m building a 28 foot table. I’m thinking that I will essentially build 4 table tops and connect them with ‘double breadboards’ with runners between the tressels (5). Thoughts? Back story: I am a veteran and I run a program that addresses PTSD, Substance Abuse and homelessness in the the veteran community. An essential component is that the veterans cook meals and eat together and as the program has grown, there is an assortment of tables in the house and I want too big a build one. I am an average woodworker and I can do the basics. It doesn’t have to be piece of art, just chunky and uniform. Also, there’s not a big endless budget so I am doing what I can. The vision: I fhave to build it in my garage and put it together on site. 28 feet long, 38 inches wide (the space dictates it). The only way I can work out the jointing is a double breadboard end that joins each section. I thought about end jointing with dowels alternating the lengths of the boards so there was no single joint across the length of the board which was quite the puzzle to figure out. 5 trestles essentially spaced under the middle breadboards with 2 runners supporting the table between legs and one runner connecting the legs 1/3 up from the bottom of the leg. Craig laseur Hi Guys, I love your podcast. I have listened to every single episode! Please keep them coming! I was listening to Episode 114 about the domino tips and I am now thinking of completing my kitchen cabinet project using dominoes instead of pocket screws for the cabinet construction as I already own a domino. I was curious as to how Brian prefers to assemble cabinets. I have already watched Guy's videos! ;) Do you use the domino? How do you go about end panel construction? How do you finish your cabinets? Any tips you can provide is greatly appreciated! Thanks, Natasha Round Lake, Ontario, Canada

Guy's Questions: Good afternoon Gentlemen, Thank you for your podcast, I really appreciate it, and you fellows. Long story short, I am a re-engaging woodworker after taking a 20 year hiatus. Due to life requirements and work travel frequency, I was unable to keep up my hobby. I now have the time (and hopefully will NEVER have to fly somewhere for work again) to start anew. Things have changed quite a bit in past couple decades, and so have my interests in terms of wood working. Over my hiatus, I sold some of my equipment in hopes the machines would be used instead of sitting idle and it is time to re-equip my shop needs with eliminated tools and new needs. My tool requirements are also much different today, then they were 20 years ago. One requirement I now have is a drum sander. I don't have the desire to rotate any work (key point), and want to acquire a machine that fits my specific needs, thus an 18" capability is perfect for what my new woodworking interests require. I also refuse to take any advice from boob tube woodworkers recommendations, as it seems that 90% of the creators I find may have started out providing woodworking content, but they mostly all just become prejudiced tool reviewers who conflict each other based on who is giving them free tools or paying them. I have lost a lot of respect for some woodworkers on YouTube who used to be considered by me as inspirations in their early YouTube careers, no longer. With that said, I have trimmed my interest list down to a Jet 1836 and Supermax 19-38. I imagine some or all of you have had experience with both, and would like your feedback. I am not currently considering models with moving/height adjustable belts such as the shop fox/grizzly, however if you have anything to add on those, it would be nice to hear. Glad you have a new host, it seems like he may be a great fit for the podcast. Well wishes to all of you, and Guy, I hope your health is well. Kurtis Van Kampen You fellas have filled my head with hours and hours of information. You’re truly the best Podcast I’ve found. So before Guy’s head begins to swell, on with the question. I’ve started watching Nee Yankee workshop again now they I actually have a 520 sqft shop to work out in. In the first season Norm used what he called a panel cutting jig for the table saw. The fence of the jig was located on the blade side rather than the operator side like the modern crosscut sled. This jig is dead simple being made of only three boards. I had big plans to make a modern crosscut sled (not the aircraft carrier) with all the bells and whistles. Now I’m completely rethinking my next table saw jig. Since Guy (like myself) is the only one of you old enough to remember the first episode, this should probably be HIS question. Keep up the great work fellows. I appreciate what each of you bring to the table. -Bryan Huy's Questions: I’d first like to say that I listen to a bunch of other woodworking podcasts as well, but of all of them, yours has the lowest level of useless off-topic banter. Keep up the good work. I have a question about the usage of my shop air cleaner. It’s a Jet AFS-1000B, and my ceiling is only 7’6”, so can’t hang it from there. So I have it on a roll-around cart. My shop is 13’ x 17’. I don’t have a central dust collection system, but for the following tools I hook up my shop vac to the tool: table saw, planer, drum sander, router table and random orbit sander. I also have a circular saw, a handheld router, a jigsaw, a drill press, a belt sander and a palm sander. My question is, for which tools should I be turning on the air cleaner, and on which setting? (it has low, medium and high settings) And how long should I keep it on for after the tool has been turned off? Thanks. Steve My perception is that the people who seem to get hurt the most are woodworking professionals who become too comfortable/familiar with machines. Is that a fair assessment? [I am a hobbyist woodworker.] FYI, on 3 I am just asking for a comment on my observation. Have a great day Chuck Brians Questions: First, love the podcast and thank you! Question: I’m building a 28 foot table. I’m thinking that I will essentially build 4 table tops and connect them with ‘double breadboards’ with runners between the tressels (5). Thoughts? Back story: I am a veteran and I run a program that addresses PTSD, Substance Abuse and homelessness in the the veteran community. An essential component is that the veterans cook meals and eat together and as the program has grown, there is an assortment of tables in the house and I want too big a build one. I am an average woodworker and I can do the basics. It doesn’t have to be piece of art, just chunky and uniform. Also, there’s not a big endless budget so I am doing what I can. The vision: I fhave to build it in my garage and put it together on site. 28 feet long, 38 inches wide (the space dictates it). The only way I can work out the jointing is a double breadboard end that joins each section. I thought about end jointing with dowels alternating the lengths of the boards so there was no single joint across the length of the board which was quite the puzzle to figure out. 5 trestles essentially spaced under the middle breadboards with 2 runners supporting the table between legs and one runner connecting the legs 1/3 up from the bottom of the leg. Craig laseur Hi Guys, I love your podcast. I have listened to every single episode! Please keep them coming! I was listening to Episode 114 about the domino tips and I am now thinking of completing my kitchen cabinet project using dominoes instead of pocket screws for the cabinet construction as I already own a domino. I was curious as to how Brian prefers to assemble cabinets. I have already watched Guy's videos! ;) Do you use the domino? How do you go about end panel construction? How do you finish your cabinets? Any tips you can provide is greatly appreciated! Thanks, Natasha Round Lake, Ontario, Canada

Cabinet Construction, Tablesaw Jigs, Keeping Your Fingers Attached and MORE!!

Brian's Questions: Hey Guys! Love the podcast. Long time listener, first time asking a question! I am looking for recommendations on how to remove saw marks after ripping pieces to final width on the table saw. I recently built a couple rocking chairs for my kiddos, and was looking for a super smooth surface finish on all four sides. My solution was to joint and plane the parts on 3 sides and then rip a 1/32 or so oversized. After that I set my jointer to 1/32 and ran the cut edge back over the jointer to remove the saw. This m I recently scored a router table on Facebook marketplace for $500. Woodpecker PRL 1 lift, Incra jig ultra fence, and Porter Cable 3.25 horse router. 1, what's your favorite lubricant for threaded parts like router lifts and table saw arbor tilts? 2, Other than keeping them clear of dust so they don't over heat is there any other maintenance to extend the life of a router? They don't make the Porter Cable routers anymore so I want to keep it in top condition. - Tylerethod seems to work nicely. I am using a Jet cabinet saw and not matter how much I try to adjust it, I can never seem to get a rip without at least a few saw marks. Just looking for ways to improve my efficiency while in the shop! Thanks again Dylan.   Hey guys, You said you needed more questions so here ya go... I have a couple hundred bucks left over from my December birthday and Christmas haul that I plan to spend on woodworking supplies/tools. I keep a running wish list throughout the year of various woodworking things I "need" So there is no shortage of things I could spend it on, however I don't want to waste it. That has encouraged me to just sit on it for now and I feel like I'm at a bit of a crossroads. Do I simply save it and put it towards a big more expensive tool down the road (for example I don't currently have any kind of planer or joiner). Or do I use it to buy some of the less sexy but more useful day to day items that every shop should have (i.e. better bits, blades, consumables, jigs, etc...) For reference: At this point in my woodworking career I do mostly hobbyist/DIY level work. I have either budget or second hand versions of most basic hand and power tools and the basic bigger tools (Benchtop Drill Press, Contractor Saw, Miter Saw) I would love to delve in to the more serious side of woodworking one day, so I do have a goal of getting a planer and joiner down the road. But realistically I know if one fell down from the heavens in to my shop tomorrow it wouldn't get used immediately. Regardless of my own personal decisions I thought it would be cool to get y'alls take on what you would consider the top small ticket items that every shop should have. I think we all get more excited about big expensive tools, because frankly it's more fun, but for people like myself just getting started on this journey it can be easy to miss the basics as a result of that excitement. Thanks for being so awesome, Jon   Guy's Questions:   Good day fellas, Been listening for a while, and really enjoy the podcast. Here is my problem/question. For Christmas this past year I made a few cutting boards as gifts using Maple, Walnut and a few pieces of Purple Heart. In my design process I managed to make one of the cutting boards slightly too big to fit (on first glue up) through my Dewalt DW735 planer. In order to save some time, I just ran the piece through the table saw to get the over width down to just under 13". On the first pass through the planer, everything went as planned. The second pass through didnt go so great. At around ¾ of the way through, the planer dug into the piece and put some pretty nasty snipe into the piece. Id say around 4-5" from the end of the board, and almost 1/8" deep. What would cause that to happen? Narrower pieces that ive ran through after havent given me any snipe since. Is it due to me using the entire 13" of the cutter head? Because of my snipe issue, im really hesitant on running anything wide through the planer now. I want to experiment using some cheaper wood, but just havent found the time to do so yet. Thanks for the help. - Dwayne   Hey guys, heard you are in need of some questions from the last show, so thought I would send one your way. What do you think is the best paint for furniture that will see use and abuse? I’ve been experimenting with some different options and haven’t found anything that I think I will stick with, and I do not want to put a clear coat over the paint. Looking for something very hard and durable, as the next time I need it will be for chairs. Any suggestions would be much appreciated. Thanks!   Huy's Questions:   When does something cross the line between being 'handmade' and 'machine made'? My nephew had a CNC machine and advertised the products as 'handmade.' Is this all subjective anyways? Have a great day Chuck

Brian's Questions: Hey Guys! Love the podcast. Long time listener, first time asking a question! I am looking for recommendations on how to remove saw marks after ripping pieces to final width on the table saw. I recently built a couple rocking chairs for my kiddos, and was looking for a super smooth surface finish on all four sides. My solution was to joint and plane the parts on 3 sides and then rip a 1/32 or so oversized. After that I set my jointer to 1/32 and ran the cut edge back over the jointer to remove the saw. This m I recently scored a router table on Facebook marketplace for $500. Woodpecker PRL 1 lift, Incra jig ultra fence, and Porter Cable 3.25 horse router. 1, what's your favorite lubricant for threaded parts like router lifts and table saw arbor tilts? 2, Other than keeping them clear of dust so they don't over heat is there any other maintenance to extend the life of a router? They don't make the Porter Cable routers anymore so I want to keep it in top condition. - Tylerethod seems to work nicely. I am using a Jet cabinet saw and not matter how much I try to adjust it, I can never seem to get a rip without at least a few saw marks. Just looking for ways to improve my efficiency while in the shop! Thanks again Dylan. Hey guys, You said you needed more questions so here ya go... I have a couple hundred bucks left over from my December birthday and Christmas haul that I plan to spend on woodworking supplies/tools. I keep a running wish list throughout the year of various woodworking things I "need" So there is no shortage of things I could spend it on, however I don't want to waste it. That has encouraged me to just sit on it for now and I feel like I'm at a bit of a crossroads. Do I simply save it and put it towards a big more expensive tool down the road (for example I don't currently have any kind of planer or joiner). Or do I use it to buy some of the less sexy but more useful day to day items that every shop should have (i.e. better bits, blades, consumables, jigs, etc...) For reference: At this point in my woodworking career I do mostly hobbyist/DIY level work. I have either budget or second hand versions of most basic hand and power tools and the basic bigger tools (Benchtop Drill Press, Contractor Saw, Miter Saw) I would love to delve in to the more serious side of woodworking one day, so I do have a goal of getting a planer and joiner down the road. But realistically I know if one fell down from the heavens in to my shop tomorrow it wouldn't get used immediately. Regardless of my own personal decisions I thought it would be cool to get y'alls take on what you would consider the top small ticket items that every shop should have. I think we all get more excited about big expensive tools, because frankly it's more fun, but for people like myself just getting started on this journey it can be easy to miss the basics as a result of that excitement. Thanks for being so awesome, Jon Guy's Questions: Good day fellas, Been listening for a while, and really enjoy the podcast. Here is my problem/question. For Christmas this past year I made a few cutting boards as gifts using Maple, Walnut and a few pieces of Purple Heart. In my design process I managed to make one of the cutting boards slightly too big to fit (on first glue up) through my Dewalt DW735 planer. In order to save some time, I just ran the piece through the table saw to get the over width down to just under 13". On the first pass through the planer, everything went as planned. The second pass through didnt go so great. At around ¾ of the way through, the planer dug into the piece and put some pretty nasty snipe into the piece. Id say around 4-5" from the end of the board, and almost 1/8" deep. What would cause that to happen? Narrower pieces that ive ran through after havent given me any snipe since. Is it due to me using the entire 13" of the cutter head? Because of my snipe issue, im really hesitant on running anything wide through the planer now. I want to experiment using some cheaper wood, but just havent found the time to do so yet. Thanks for the help. - Dwayne Hey guys, heard you are in need of some questions from the last show, so thought I would send one your way. What do you think is the best paint for furniture that will see use and abuse? I’ve been experimenting with some different options and haven’t found anything that I think I will stick with, and I do not want to put a clear coat over the paint. Looking for something very hard and durable, as the next time I need it will be for chairs. Any suggestions would be much appreciated. Thanks! Huy's Questions: When does something cross the line between being 'handmade' and 'machine made'? My nephew had a CNC machine and advertised the products as 'handmade.' Is this all subjective anyways? Have a great day Chuck

Jointing Edges, Painted Furniture, Is It Still Handmade? and MORE!

Brians Questions:  Hi Friends: I really enjoy every podcast you guys put out. Thanks to Brain for stepping up to be the third host. He seems to be a natural with podcasting and teaching woodworking techniques. My question is related to tool choice. I am currently planning to build out a router table into the black phenolic extension table for my sawstop PCS 175. I have the 36inch cut capacity. I have seen videos on modifiying the extension table and dropping in a router lift. It seems like a great shop space saver. I have two questions for you guys. Do you think there is any value in having a stand alone router table? or is modifying the phenolic table a reasonable approach. I plan to build a custom fence to attach to the sawstop fence. My second question is - how important is it to buy a full size (3.25hp) router versus just getting a mid size router (2.25hp)? I currently have the milwaukee battery powered palm router (1.25hp) which has been useful but I want the accuracy and stability of a router table. The bulk of my work is edging and dados, but I would like the capacity to do raised panel cabinet doors and even to take my router out of the table and eventually build a flattening jig for large slabs. Is 2.25hp enough for these tasks? I am a hobbyist and don't have any production needs for this setup but don't want to be limited. Accuracy is important to me so I am going to go with a lift rather than buying a router with a base that can be screwed onto a table (like the triton). One issue is that a lift + router setup for a 2.25hp router is about $350 and for 3.25hp, I'm looking at $800+. Thaks in advance for your thoughts Sincerely, Jeremy Los Angeles, CA ey guys I just wrote in and submitted a question but I do have another which I hope can be answered I’m building a kitchen table, 36x60” with a 1.5” top. The table is being made out of Rustic Rift Sawn White Oak Question is what is the best or a best method to ensure the top stays flat. This is in San Diego, Ca so weather/ humidity changes are the quite mild. I was thinking maple cleats across the bottom/ not glued but screwed allowing for movement. Any suggestions would be great Thanks and can’t wait for the next episode Nicholas   Guy's Questions: 1. What are the best responses to people who want you to make them something (usually for little or nothing)? [Most people are clueless regarding the effort and expense it takes to make something nice.] Have a great day Chuck Hello all, the WoodMech here, I just purchased a ts55 festool tracksaw with the 55” guide rail for my kitchen remodeling project. I was wondering how accurate joining two tracks together compared to having the longer track? I was thinking about getting the guide rail with the shelf pin spacing holes and using that as the extension for cutting length wise on sheets of plywood. What are your thoughts or experiences? Thanks for the great show! Jeff Baran   Huy's Questions: Gentlemen and Guy :) Have been listening for about a year and this is still the best woodworking podcast out there. I'd also like to thanks Sean for his contributions and welcome Brian to the show! My question is, there are so many woodworking content makers out there today. Who are the woodworkers that you guys follow ?? Second question... Assume you have become retired and now have lots of time on your hands. What woodworking projects would you work on? Would you go into production work and sell your goods, custom furniture??? What would be your ultimate retired woodworking project??? Thanks ! Liam Indianapolis, IN So I'm having trouble with bubbles. Both when I'm using epoxy and fast drying/instant glue (Starbond) any advice on how to avoid them? I'm not doing large pours, this is simply some gap filling and knot hole stabilization. With the Starbond I do use their accelerator, but I've done it with and without, and it doesn't seem to make a difference w/r/t the bubbles. Also, how do you get the glue/epoxy down into a pin hole? Mark Bett

Brians Questions:  Hi Friends: I really enjoy every podcast you guys put out. Thanks to Brain for stepping up to be the third host. He seems to be a natural with podcasting and teaching woodworking techniques. My question is related to tool choice. I am currently planning to build out a router table into the black phenolic extension table for my sawstop PCS 175. I have the 36inch cut capacity. I have seen videos on modifiying the extension table and dropping in a router lift. It seems like a great shop space saver. I have two questions for you guys. Do you think there is any value in having a stand alone router table? or is modifying the phenolic table a reasonable approach. I plan to build a custom fence to attach to the sawstop fence. My second question is - how important is it to buy a full size (3.25hp) router versus just getting a mid size router (2.25hp)? I currently have the milwaukee battery powered palm router (1.25hp) which has been useful but I want the accuracy and stability of a router table. The bulk of my work is edging and dados, but I would like the capacity to do raised panel cabinet doors and even to take my router out of the table and eventually build a flattening jig for large slabs. Is 2.25hp enough for these tasks? I am a hobbyist and don't have any production needs for this setup but don't want to be limited. Accuracy is important to me so I am going to go with a lift rather than buying a router with a base that can be screwed onto a table (like the triton). One issue is that a lift + router setup for a 2.25hp router is about $350 and for 3.25hp, I'm looking at $800+. Thaks in advance for your thoughts Sincerely, Jeremy Los Angeles, CA ey guys I just wrote in and submitted a question but I do have another which I hope can be answered I’m building a kitchen table, 36x60” with a 1.5” top. The table is being made out of Rustic Rift Sawn White Oak Question is what is the best or a best method to ensure the top stays flat. This is in San Diego, Ca so weather/ humidity changes are the quite mild. I was thinking maple cleats across the bottom/ not glued but screwed allowing for movement. Any suggestions would be great Thanks and can’t wait for the next episode Nicholas Guy's Questions: 1. What are the best responses to people who want you to make them something (usually for little or nothing)? [Most people are clueless regarding the effort and expense it takes to make something nice.] Have a great day Chuck Hello all, the WoodMech here, I just purchased a ts55 festool tracksaw with the 55” guide rail for my kitchen remodeling project. I was wondering how accurate joining two tracks together compared to having the longer track? I was thinking about getting the guide rail with the shelf pin spacing holes and using that as the extension for cutting length wise on sheets of plywood. What are your thoughts or experiences? Thanks for the great show! Jeff Baran Huy's Questions: Gentlemen and Guy :) Have been listening for about a year and this is still the best woodworking podcast out there. I'd also like to thanks Sean for his contributions and welcome Brian to the show! My question is, there are so many woodworking content makers out there today. Who are the woodworkers that you guys follow ?? Second question... Assume you have become retired and now have lots of time on your hands. What woodworking projects would you work on? Would you go into production work and sell your goods, custom furniture??? What would be your ultimate retired woodworking project??? Thanks ! Liam Indianapolis, IN So I'm having trouble with bubbles. Both when I'm using epoxy and fast drying/instant glue (Starbond) any advice on how to avoid them? I'm not doing large pours, this is simply some gap filling and knot hole stabilization. With the Starbond I do use their accelerator, but I've done it with and without, and it doesn't seem to make a difference w/r/t the bubbles. Also, how do you get the glue/epoxy down into a pin hole? Mark Bett

Yes or No to a RouterTable, Track Saws, Bubbles and MORE!

Brians Questions: Good evening everyone, Wanted to reach out to you about time in the shop. Im expecting my second child in a matter of days and was curious how you all find/found time in the shop with little kids running around and being constantly tired? My second question is a follow up regarding a question you all read regarding "Box Materials" on October 20th. Loved the double answer but was looking for Drawer box material to use. BB (or whatever you can find now) or a hardwood? Thanks, Paul at Twin Lake Woodshop Hey guys love the podcast. I have been listening for a while now and hear you need some questions. What has been your favorite thing to build and why? something you’ve built in the past or even something you would like to build in the future. Please share how you built it (or want to build it) and what it was (or will be) enjoyable about the project. Thanks for all the great content and hopefully I’ll bring some more specific questions in the near future. -Nicholas Guys Questions: Long time listener, first time caller. You guys have mentioned water-based conversion varnish and that you can get it pigmented. I hate painting woodworking projects, but the wife wants what she wants. Why do you prefer conversion varnish and is there a certain product you prefer? I have a five stage Apollo sprayer, so spraying shouldn't be a problem. I live on the southside of Indianapolis so it isn't the easiest place to get supplies. Thanks, Geoff Hi Fellas, I found the podcast a few months ago and have been really enjoying it. Thanks for the great content and knowledge. I am very much a novice woodworker so I have lots of questions. Sounds like you need questions and I would love some answers so maybe we can all come out on top here. Probably me more than you. Question #1 of 2. I have a little doweling jig, I think from Rockler. It gets the job done, but just barely. I would really like to upgrade to something that is more efficient but more importantly, that is more versatile. I want something with adjustable height and that can do acute angles. I would love a domino but its out of my price range right now. I saw that grizzly, triton and mafell all make a doweling joiner similar to a domino. Yes, one of these things is not like the other. The mafell looks incredible but it costs more than the domino. The triton and grizzly look fine and are very reasonably priced but the reviews tell me they probably aren’t worth spending the money. The dowelmax system looks great but its only does 90° and 45°, and you have to buy the 45° adapter plate. After all that, I may as well save a little longer and get the domino. My questions is: should I risk it with the triton, get a biscuit joiner (which I’m worried won’t have enough strength for certain applications) or just keep saving and get a domino down the road? Or is there another product I don’t know about? Thanks. Happy New Year! Jon Moch Huy's Questions: I have been given a mission to make a wooden serving dish. The shape is basically an elongated oval. Dimensions are 21" x 9" x 1 1/2". My patron (hum hum) called the design a fish platter. Wood will probably be walnut. The walls of the dish are to be sloped and just slightly curved. With some hand work I think I can achieve the outside wall of the dish. The issue creating the most questions for me is how to do the inside wall of the dish. I have seen plenty of bowl and tray bottom router bits. All cut a vertical wall. Bevel router bits I have seen have a bearing on the bottom. The bearing would interfere with the bottom of the dish. Because of the inside and outside curve of the wall I doubt if making a custom scratch stock would yield good results. I don't want to get into the CNC rabbit hole. Any thoughts? You have a great podcast and provide a valuable service to the wood working community. Cheers, Bob On one of the kitchen tables that I made I used mortise-and-tenon joinery, which turned out well, with everything plumb, and then to make sure it was strong I also put in a corner brace cut at 45-degrees, screwed into the skirt on each side, and then ran a cabinet screw through that corner brace into the leg. I left a small gap, about 1/16" between the corner brace and the leg. When I tightened up the braces the legs splayed out a little bit, making them not quite plumb. My concern with seeing the leg move is that I may have stressed the tenons (although I didn't hear any cracking). Is the best practice to omit this corner bracing when doing mortise-and-tenon tables? Mark Schmidt

Brians Questions: Good evening everyone, Wanted to reach out to you about time in the shop. Im expecting my second child in a matter of days and was curious how you all find/found time in the shop with little kids running around and being constantly tired? My second question is a follow up regarding a question you all read regarding "Box Materials" on October 20th. Loved the double answer but was looking for Drawer box material to use. BB (or whatever you can find now) or a hardwood? Thanks, Paul at Twin Lake Woodshop Hey guys love the podcast. I have been listening for a while now and hear you need some questions. What has been your favorite thing to build and why? something you’ve built in the past or even something you would like to build in the future. Please share how you built it (or want to build it) and what it was (or will be) enjoyable about the project. Thanks for all the great content and hopefully I’ll bring some more specific questions in the near future. -Nicholas Guys Questions: Long time listener, first time caller. You guys have mentioned water-based conversion varnish and that you can get it pigmented. I hate painting woodworking projects, but the wife wants what she wants. Why do you prefer conversion varnish and is there a certain product you prefer? I have a five stage Apollo sprayer, so spraying shouldn't be a problem. I live on the southside of Indianapolis so it isn't the easiest place to get supplies. Thanks, Geoff Hi Fellas, I found the podcast a few months ago and have been really enjoying it. Thanks for the great content and knowledge. I am very much a novice woodworker so I have lots of questions. Sounds like you need questions and I would love some answers so maybe we can all come out on top here. Probably me more than you. Question #1 of 2. I have a little doweling jig, I think from Rockler. It gets the job done, but just barely. I would really like to upgrade to something that is more efficient but more importantly, that is more versatile. I want something with adjustable height and that can do acute angles. I would love a domino but its out of my price range right now. I saw that grizzly, triton and mafell all make a doweling joiner similar to a domino. Yes, one of these things is not like the other. The mafell looks incredible but it costs more than the domino. The triton and grizzly look fine and are very reasonably priced but the reviews tell me they probably aren’t worth spending the money. The dowelmax system looks great but its only does 90° and 45°, and you have to buy the 45° adapter plate. After all that, I may as well save a little longer and get the domino. My questions is: should I risk it with the triton, get a biscuit joiner (which I’m worried won’t have enough strength for certain applications) or just keep saving and get a domino down the road? Or is there another product I don’t know about? Thanks. Happy New Year! Jon Moch Huy's Questions: I have been given a mission to make a wooden serving dish. The shape is basically an elongated oval. Dimensions are 21" x 9" x 1 1/2". My patron (hum hum) called the design a fish platter. Wood will probably be walnut. The walls of the dish are to be sloped and just slightly curved. With some hand work I think I can achieve the outside wall of the dish. The issue creating the most questions for me is how to do the inside wall of the dish. I have seen plenty of bowl and tray bottom router bits. All cut a vertical wall. Bevel router bits I have seen have a bearing on the bottom. The bearing would interfere with the bottom of the dish. Because of the inside and outside curve of the wall I doubt if making a custom scratch stock would yield good results. I don't want to get into the CNC rabbit hole. Any thoughts? You have a great podcast and provide a valuable service to the wood working community. Cheers, Bob On one of the kitchen tables that I made I used mortise-and-tenon joinery, which turned out well, with everything plumb, and then to make sure it was strong I also put in a corner brace cut at 45-degrees, screwed into the skirt on each side, and then ran a cabinet screw through that corner brace into the leg. I left a small gap, about 1/16" between the corner brace and the leg. When I tightened up the braces the legs splayed out a little bit, making them not quite plumb. My concern with seeing the leg move is that I may have stressed the tenons (although I didn't hear any cracking). Is the best practice to omit this corner bracing when doing mortise-and-tenon tables? Mark Schmidt

Finding Shop Time, Using Dowels, Securing Table Legs AND MORE!

Guys Questions: Hey guys. I just finished listening to your latest podcast, really good information and insight as usual. I'm still a novice user of the Domino so really enjoyed the tips and tricks you provided in answering a Domino related question. You mentioned being very short on questions so I'm going to send a similar question to one sent a couple of months ago that didn't get answered. I built an outfeed table a couple of years ago to use solely as an extension of my table saw. Now I find that I use it for glue-ups, as an assembly table and just about every other task. The table is roughly 44" x 44". I would now like to rebuild it as a true multi-functional table with the proper hold-downs and clamping devices and could use some design advice from you based upon the pros and cons you find with your own MFT's. One particular area I'm interesting in is the size of dog holes to use (imperial vs metric) and some recommendations on the type of dogs and clamping devices I should buy to get the best use of the MFT. Thanks again for having by far the best woodworking podcast available. And Brian, welcome to the team. Jack Francis Geneva, IL Happy New Year Guys, and welcome Brian. Guy and Huy have been kind enough to answer a number of my questions in the past (and Huy has always been helpful in making me spend money lol). With my last question you helped me convince myself to invest in a CNC which is on order now, and after watching Guy’s video on his 3D Printer (and he was kind enough to answer a question on the video for me) I was wondering if you three would expand on your thoughts on CNC, 3-D printing, and Lasers in the wood shop for the hobbyist woodworking. I foresee having all three in my arsenal at some point in the near future. Thanks as always and I look forward to your insights, Doug Brians Questions: Fellow travelers on this path of wood- First off, there has to be a better way of saying that. Secondly, I don't think I have told you recently how much I am enjoying the podcast, and your new addition Brian. At first I was like "two hosts from Indiana and I don't even believe that state actually exists," but you've won me over. On to my question. I find myself wanting maple doors for my house, but I need...13 to start for the upstairs. And I want them to be curly maple. So, because I got into woodworking to save money (duh), I'm going to build them myself. 4-panel Shaker style interior doors ranging from 24" to 36" wide. Would you recommend using maple ply for the panels, or glueing up stock? Honestly my concern isn't so much wood movement as the P.I.T.A. it would be to make all those panels (Pain in the...). And while we are on the subject of pains in the posterior, would you recommend a Domino or Lamello, save me a few minutes on those mortice and tenons, or just jig it up? Unfortunately I think the hand tools have to sit on the sidelines for this one. Thank you for your sage advice. Excelsior! - Tom Figura Hi Guy, Huy, and Brian, Thank you for the very informative podcast, I’ve been listening for years. The knowledge that I’ve gained from the Woodshop Life podcast helps me make my limited time in the shop way more efficient. Thank you for generously sharing your wisdom. Question for you guys about sheet good selection. What sheet goods do you typically use for the projects in your shop and what is your thought process when deciding if if a particular project should use Baltic Birch, common 7 layer plywood, MDF, etc.? Baltic Birch is the premium grade option, but do you use it for projects such as shop cabinets, sleds, and fixtures? Thank you, Dominic Santa Cruz, CA Huy's Questions: Hello. My question is regarding the placement of a dust collector. I have a 250 SF shop so every SF is precious. I am a hobbyist woodworker/DIYer. My current dust collection is a shop-vac with a dust-stopper bucket separator in a cart. 1 hose, all my tools and multiple converters to fit each tool. The cart doubles as an outfeed table for the table saw. I have an open rafter ceiling with a storage floor in it (currently filled with crap I should get rid of). I am considering a more powerful collector and ducting to 2 machines (miter and table saw) and to a boom arm that can be used for miscellaneous tools (skill saw, drill press etc.). I'm looking at the Jet DC-650MK or something similar (1 -2 HP, $600 - $800ish ranges. So finally, my question: Could a system like this be mounted in that attic storage above the shop and function correctly? Any obvious issues I'd run into? I have simple pully system for getting the full bag from there to the main floor. A couple of concerns are performance issues based on the elevated height, safety (I don't really have any concerns, but this is totally a "I don't know what I don't know" situation) and???? I love the podcast guys. I binged all of your episodes during the height of the pandemic (summer of 2020) and just loved it. I took a break for more than a year but I'm back, and I'm so glad you're still here! Best regards, Michael Hey Guys. Ive been woodworking for a couple years now and really enjoy the show to learn the fundamentals. I’m currently planning a walnut tv stand build and have a question about box bottoms. The piece will have two support legs (one on either side), a low shelf and a 8 inch deep box on the top spanning the 48 inch width between the legs. The box on the top will have a lid opening from the top similar to a blanket chest and be used to hold exercise dumbbells which collectively weight about 200 lbs. my question is… how should I make the box bottom so that it can support so much weight without any extra supports across the 48 inch span? Hardwood? plywood? Dado a groove for the bottom? From what I can tell online, it might make the most sense to use 3/4 ply and a 3/4 dado however my understand is that the recess below the dado should be the same width as the ply which will leave a 3/4 deep recess under the box that might be noticeable since it’s floating above the lower shelf. Also in a 8 inch tall box, I will be losing precious storage space quickly. I was thinking about cutting a rabbet in the ply to insert only a 1/2 inch in the groove and fill some of the recess under the box bottom but I’m not sure about strength. Maybe I could get away with just 1/2 inch ply in that case? The carcass of the rest of box will be made of solid walnut. I hope that all made sense. Thanks a lot for your thoughts. -Tyler

Guys Questions: Hey guys. I just finished listening to your latest podcast, really good information and insight as usual. I'm still a novice user of the Domino so really enjoyed the tips and tricks you provided in answering a Domino related question. You mentioned being very short on questions so I'm going to send a similar question to one sent a couple of months ago that didn't get answered. I built an outfeed table a couple of years ago to use solely as an extension of my table saw. Now I find that I use it for glue-ups, as an assembly table and just about every other task. The table is roughly 44" x 44". I would now like to rebuild it as a true multi-functional table with the proper hold-downs and clamping devices and could use some design advice from you based upon the pros and cons you find with your own MFT's. One particular area I'm interesting in is the size of dog holes to use (imperial vs metric) and some recommendations on the type of dogs and clamping devices I should buy to get the best use of the MFT. Thanks again for having by far the best woodworking podcast available. And Brian, welcome to the team. Jack Francis Geneva, IL Happy New Year Guys, and welcome Brian. Guy and Huy have been kind enough to answer a number of my questions in the past (and Huy has always been helpful in making me spend money lol). With my last question you helped me convince myself to invest in a CNC which is on order now, and after watching Guy’s video on his 3D Printer (and he was kind enough to answer a question on the video for me) I was wondering if you three would expand on your thoughts on CNC, 3-D printing, and Lasers in the wood shop for the hobbyist woodworking. I foresee having all three in my arsenal at some point in the near future. Thanks as always and I look forward to your insights, Doug Brians Questions: Fellow travelers on this path of wood- First off, there has to be a better way of saying that. Secondly, I don't think I have told you recently how much I am enjoying the podcast, and your new addition Brian. At first I was like "two hosts from Indiana and I don't even believe that state actually exists," but you've won me over. On to my question. I find myself wanting maple doors for my house, but I need...13 to start for the upstairs. And I want them to be curly maple. So, because I got into woodworking to save money (duh), I'm going to build them myself. 4-panel Shaker style interior doors ranging from 24" to 36" wide. Would you recommend using maple ply for the panels, or glueing up stock? Honestly my concern isn't so much wood movement as the P.I.T.A. it would be to make all those panels (Pain in the...). And while we are on the subject of pains in the posterior, would you recommend a Domino or Lamello, save me a few minutes on those mortice and tenons, or just jig it up? Unfortunately I think the hand tools have to sit on the sidelines for this one. Thank you for your sage advice. Excelsior! - Tom Figura Hi Guy, Huy, and Brian, Thank you for the very informative podcast, I’ve been listening for years. The knowledge that I’ve gained from the Woodshop Life podcast helps me make my limited time in the shop way more efficient. Thank you for generously sharing your wisdom. Question for you guys about sheet good selection. What sheet goods do you typically use for the projects in your shop and what is your thought process when deciding if if a particular project should use Baltic Birch, common 7 layer plywood, MDF, etc.? Baltic Birch is the premium grade option, but do you use it for projects such as shop cabinets, sleds, and fixtures? Thank you, Dominic Santa Cruz, CA Huy's Questions: Hello. My question is regarding the placement of a dust collector. I have a 250 SF shop so every SF is precious. I am a hobbyist woodworker/DIYer. My current dust collection is a shop-vac with a dust-stopper bucket separator in a cart. 1 hose, all my tools and multiple converters to fit each tool. The cart doubles as an outfeed table for the table saw. I have an open rafter ceiling with a storage floor in it (currently filled with crap I should get rid of). I am considering a more powerful collector and ducting to 2 machines (miter and table saw) and to a boom arm that can be used for miscellaneous tools (skill saw, drill press etc.). I'm looking at the Jet DC-650MK or something similar (1 -2 HP, $600 - $800ish ranges. So finally, my question: Could a system like this be mounted in that attic storage above the shop and function correctly? Any obvious issues I'd run into? I have simple pully system for getting the full bag from there to the main floor. A couple of concerns are performance issues based on the elevated height, safety (I don't really have any concerns, but this is totally a "I don't know what I don't know" situation) and???? I love the podcast guys. I binged all of your episodes during the height of the pandemic (summer of 2020) and just loved it. I took a break for more than a year but I'm back, and I'm so glad you're still here! Best regards, Michael Hey Guys. Ive been woodworking for a couple years now and really enjoy the show to learn the fundamentals. I’m currently planning a walnut tv stand build and have a question about box bottoms. The piece will have two support legs (one on either side), a low shelf and a 8 inch deep box on the top spanning the 48 inch width between the legs. The box on the top will have a lid opening from the top similar to a blanket chest and be used to hold exercise dumbbells which collectively weight about 200 lbs. my question is… how should I make the box bottom so that it can support so much weight without any extra supports across the 48 inch span? Hardwood? plywood? Dado a groove for the bottom? From what I can tell online, it might make the most sense to use 3/4 ply and a 3/4 dado however my understand is that the recess below the dado should be the same width as the ply which will leave a 3/4 deep recess under the box that might be noticeable since it’s floating above the lower shelf. Also in a 8 inch tall box, I will be losing precious storage space quickly. I was thinking about cutting a rabbet in the ply to insert only a 1/2 inch in the groove and fill some of the recess under the box bottom but I’m not sure about strength. Maybe I could get away with just 1/2 inch ply in that case? The carcass of the rest of box will be made of solid walnut. I hope that all made sense. Thanks a lot for your thoughts. -Tyler

Assembly Tables, Shop Furniture, 3D Printing and MORE!

Guys Questions: Hey gentlemen, welcome Brian. I have a commission for a big walnut slab table that will live in a nook with windows on 3 sides (lots of UV exposure). What do you recommend for finishing. I seem to recall Guy mentioning some walnut finishes don’t hold up well to UV exposure. I’m probably a month out from delivery so hopefully this makes it to the show before then! Sincerely your accidentental woodworking fabricator. Will In the past I’ve done a few small veneering projects and am currently working on one which will require a few larger panels- about 24”x 31”. Previously I used a train-load of clamps and cauls to press the veneer but now I want to step up my game so I ordered a vacuum press. Thanks to a few of Guy’s videos the process seems pretty straightforward but I do have a question on the glue. For veneering my only experience is with Titebond cold press veneer glue with good results but in some videos I’ve seen some folks recommend Urea-formaldehyde glue - especially for larger panels. Do any of you have experience with this stuff? Sounds a bit nasty but if it’s better for the application I’ll give it a shot. Thanks! Jeffrey Brians Questions: Been listening to the podcast for a couple years now, and while I'm sorry to see Sean step away for now, I'm happy that you found someone willing to chip in! Two things, both mainly for Brian. One, you've mentioned that you don't have much of a social media presence or any way to really show case your work. While a lot of people do turn to Facebook, Instagram, etc. for this... I wonder if maybe simply an account on SimpleCove.com (Sean's website) might be a good fit? Two... work bench. Lots of questions - what style are you planning (Roubo, Nicholson, Moravian, Shaker, hybrid, something else?), size, what kind of wood are you thinking of using - fancy with hardwoods, or something simpler ala Siemensen's Naked Woodworker bench or Schwarz's Anarchist Workbench (both 2x construction lumber)? I think you'd mentioned still being up in the air about vise hardware - are you leaning towards wood screws like Lake Erie Toolworks, or metal like Benchcrafted? Maybe Hovarter, which has some quick-release options? And then the really big question... dog holes. Round or square? Answer carefully ;) I'm one of those people who has to fight the urge to build almost every bench design I see. Started with a Nicholson, but kind of went off in a weird direction with it and didn't like how it turned out. Deconstructed it and re-purposed most of the lumber for other projects. Couldn't make up my mind what I wanted to build next (not enough room for one of each!) so I put some inexpensive import (Yost) vises on a utility bench in the shop, and have been living with that for now. Not ideal, but it's letting me work out a few ideas on a trial basis before I have to commit. Very much looking forward to hearing (or seeing) more about your bench project! - Monte Thank you all for spreading the knowledge and answering questions. I find myself building more cabinets lately out of plywood and I'm edge banding them with solid lumber (I go with 5/16 on the banding). I cut the banding a little wider than the sheet goods, glue it on and then trim it flush. I'm running into some issues during the trimming that I'm hoping you guys can chime in on. Often times, when I'm trimming the banding I get a little gouge here and there on the face veneer. It's not a huge deal on paint grade stuff but when I'm using something like walnut, cherry or white oak ply, it becomes a problem. What tips do you have for trimming the edge banding cleanly and efficiently without damaging the veneer? Below are some things I've tried and some of my experiences with these methods. I'm curious if you have other methods, or if you have some tips to improve what I'm already doing. Things I've tried so far: - Router balanced on the edge - so far the worst method. Too tippy and additional supports can take a while to set up, with ocasional slipups still. - Router jig - I saw Fredie @periodcraftsmen share a jig for flush triming the edge banding and I copied it. The jig has a flat wide reference face that rides on the panel face (laid flat) and it has a 90 degree fence that holds up a trim router horizontally. Using a downcut bit, the router is adjusted so that the bit is almost flush to the reference face and it trims the edgebanding protruding above the flat face. I hope you can picture that. This gives good results but I ocasionally run into issues at the start and end of the panel where the jig may want to tip a bit and bite into the face. - Tall fence on the table saw - using it kind of like an L-fence, the sacrificial face is set up above the blade and flush with the outer teeth. The panel rides the fence vertically and the edgbanding rides under the fence where it gets trimmed off. This so far gives the best results especially when I went to an extra tall fence to give it more of a bearing surface and not let the panel tip. Ocasionally the panel is a bit bowed which gives it a bit of trouble and it can be a bit unwieldy if the panel is large. Can be hard to keep it flat on a long panel. It is fast though. - Hand plane - using a block plane carefully work it down. I have still bit into it a few times when not careful but this is overall the most accurate method. It is slow though and can be a pain if there is a lot of trimming. - Bojan Huy's Questions: When you're building a piece of furniture (like a dresser), do you follow a specific order? Like cutting everything first, arming (make sure that everything works), disarming. Karel I love your podcast. You try hard to fully answer questions asked and not provide flippant answers like other shows do. That’s what makes this show great. Now to my question. I have been wanting to upgrade my sanding game. I want to reduce the vibration, have it stop quickly, and produce a great result. I would love to hear your thoughts on what you look for in sanders such as the size (5 or 6 in), pad types (soft through hard), brands you have used and liked, and what brand of paper you buy. I’m starting to realize no one sander does it all anymore, so do you have a progression of sander purchases you would make for a simple furniture maker? Thanks you for anything you provide. - Brian Russell

Guys Questions: Hey gentlemen, welcome Brian. I have a commission for a big walnut slab table that will live in a nook with windows on 3 sides (lots of UV exposure). What do you recommend for finishing. I seem to recall Guy mentioning some walnut finishes don’t hold up well to UV exposure. I’m probably a month out from delivery so hopefully this makes it to the show before then! Sincerely your accidentental woodworking fabricator. Will In the past I’ve done a few small veneering projects and am currently working on one which will require a few larger panels- about 24”x 31”. Previously I used a train-load of clamps and cauls to press the veneer but now I want to step up my game so I ordered a vacuum press. Thanks to a few of Guy’s videos the process seems pretty straightforward but I do have a question on the glue. For veneering my only experience is with Titebond cold press veneer glue with good results but in some videos I’ve seen some folks recommend Urea-formaldehyde glue - especially for larger panels. Do any of you have experience with this stuff? Sounds a bit nasty but if it’s better for the application I’ll give it a shot. Thanks! Jeffrey Brians Questions: Been listening to the podcast for a couple years now, and while I'm sorry to see Sean step away for now, I'm happy that you found someone willing to chip in! Two things, both mainly for Brian. One, you've mentioned that you don't have much of a social media presence or any way to really show case your work. While a lot of people do turn to Facebook, Instagram, etc. for this... I wonder if maybe simply an account on <a href="http://SimpleCove.com" rel="nofollow" target="_blank">SimpleCove.com</a> (Sean's website) might be a good fit? Two... work bench. Lots of questions - what style are you planning (Roubo, Nicholson, Moravian, Shaker, hybrid, something else?), size, what kind of wood are you thinking of using - fancy with hardwoods, or something simpler ala Siemensen's Naked Woodworker bench or Schwarz's Anarchist Workbench (both 2x construction lumber)? I think you'd mentioned still being up in the air about vise hardware - are you leaning towards wood screws like Lake Erie Toolworks, or metal like Benchcrafted? Maybe Hovarter, which has some quick-release options? And then the really big question... dog holes. Round or square? Answer carefully ;) I'm one of those people who has to fight the urge to build almost every bench design I see. Started with a Nicholson, but kind of went off in a weird direction with it and didn't like how it turned out. Deconstructed it and re-purposed most of the lumber for other projects. Couldn't make up my mind what I wanted to build next (not enough room for one of each!) so I put some inexpensive import (Yost) vises on a utility bench in the shop, and have been living with that for now. Not ideal, but it's letting me work out a few ideas on a trial basis before I have to commit. Very much looking forward to hearing (or seeing) more about your bench project! - Monte Thank you all for spreading the knowledge and answering questions. I find myself building more cabinets lately out of plywood and I'm edge banding them with solid lumber (I go with 5/16 on the banding). I cut the banding a little wider than the sheet goods, glue it on and then trim it flush. I'm running into some issues during the trimming that I'm hoping you guys can chime in on. Often times, when I'm trimming the banding I get a little gouge here and there on the face veneer. It's not a huge deal on paint grade stuff but when I'm using something like walnut, cherry or white oak ply, it becomes a problem. What tips do you have for trimming the edge banding cleanly and efficiently without damaging the veneer? Below are some things I've tried and some of my experiences with these methods. I'm curious if you have other methods, or if you have some tips to improve what I'm already doing. Things I've tried so far: - Router balanced on the edge - so far the worst method. Too tippy and additional supports can take a while to set up, with ocasional slipups still. - Router jig - I saw Fredie @periodcraftsmen share a jig for flush triming the edge banding and I copied it. The jig has a flat wide reference face that rides on the panel face (laid flat) and it has a 90 degree fence that holds up a trim router horizontally. Using a downcut bit, the router is adjusted so that the bit is almost flush to the reference face and it trims the edgebanding protruding above the flat face. I hope you can picture that. This gives good results but I ocasionally run into issues at the start and end of the panel where the jig may want to tip a bit and bite into the face. - Tall fence on the table saw - using it kind of like an L-fence, the sacrificial face is set up above the blade and flush with the outer teeth. The panel rides the fence vertically and the edgbanding rides under the fence where it gets trimmed off. This so far gives the best results especially when I went to an extra tall fence to give it more of a bearing surface and not let the panel tip. Ocasionally the panel is a bit bowed which gives it a bit of trouble and it can be a bit unwieldy if the panel is large. Can be hard to keep it flat on a long panel. It is fast though. - Hand plane - using a block plane carefully work it down. I have still bit into it a few times when not careful but this is overall the most accurate method. It is slow though and can be a pain if there is a lot of trimming. - Bojan Huy's Questions: When you're building a piece of furniture (like a dresser), do you follow a specific order? Like cutting everything first, arming (make sure that everything works), disarming. Karel I love your podcast. You try hard to fully answer questions asked and not provide flippant answers like other shows do. That’s what makes this show great. Now to my question. I have been wanting to upgrade my sanding game. I want to reduce the vibration, have it stop quickly, and produce a great result. I would love to hear your thoughts on what you look for in sanders such as the size (5 or 6 in), pad types (soft through hard), brands you have used and liked, and what brand of paper you buy. I’m starting to realize no one sander does it all anymore, so do you have a progression of sander purchases you would make for a simple furniture maker? Thanks you for anything you provide. - Brian Russell

How Does UV Light Effect Finish, Which Style of Workbench, Sanding Tips and MORE!

Support us on Patreon: https://www.patreon.com/woodshoplife Guy's Questions: Hey guys, Have a, “what is your favorite finish” question. While this has been asked and answered a thousand times, I’m struggling to find a good answer for my scenario. I’m putting up a pine tongue and groove wall in a small bathroom. What would you suggest for the best and easiest application for finishing a wood bathroom wall with irregular surfaces? I want a slightly amber but not darkening, matte to approaching semi-gloss finish. I prefer to prefinish the uncut boards and cut to fit. Preferred options for finish application are either my electric spray gun or wipe on finish…although with the irregular surface I don’t want a difficult wipe on finish option. -Zack Hey guys, I enjoy the podcast. I recently got a festool domino. I wanted to see if you guys could provide some tips that would help a new user. Also if you have bought or made some jigs that you would recommend. Thanks, Scott Birmingham, AL Brian's Questions: Hello! I hope you all are doing well! I live in the great state of Alabama just up the road a short bit from Huy in Toney. I greatly enjoy your podcast as it is definitely the best one on the subject of woodworking! I would consider myself a hobbyist woodworker although, I have built some commissioned pieces. I have a Ridgid contractor saw mounted to the mobile stand that it came with. I use this saw for all sorts of projects, including ripping full sheets of plywood. My question is concerning the riving knife. Are there any benefits to the dang thing? I may have bent mine during a previous operation but, it seems to me that it just gets in the way and prevents me from being able to move material smoothly through the blade and is causing burning in some or most of my cuts. Also, I am using the blade that came with the saw. Should I swap to a different blade? Is the brand of blade as important as the type of blade? Thank you very much for answering my questions and I look forward to listening to many more episodes of the podcast. Juston Bohannan Huys' Questions: I thought these two might lead to some good conversations. 1. If you were to build a set of dining chairs. What is your absolute tool you couldn’t do without. Would it be a domino or would you spring for a panto router. Maybe a shaper origin. 2. Besides a captured veneered panel could you get away with 1/16 veneers on one side and 3/32 backing veneers on the other side on a panel? Essentially would you veneer a panel with different thickness of veneers on either side. Reason I ask I might make a builtin shelving unit with 1/16” veneer on the front and some 3/32 backing veneer on the back side that faces the wall. It would be captured with the cabinet carcass dado so I would assume it wouldn’t potato chip. But who knows. Jesse @ beechlandfurniture

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guy's Questions: Hey guys, Have a, “what is your favorite finish” question. While this has been asked and answered a thousand times, I’m struggling to find a good answer for my scenario. I’m putting up a pine tongue and groove wall in a small bathroom. What would you suggest for the best and easiest application for finishing a wood bathroom wall with irregular surfaces? I want a slightly amber but not darkening, matte to approaching semi-gloss finish. I prefer to prefinish the uncut boards and cut to fit. Preferred options for finish application are either my electric spray gun or wipe on finish…although with the irregular surface I don’t want a difficult wipe on finish option. -Zack Hey guys, I enjoy the podcast. I recently got a festool domino. I wanted to see if you guys could provide some tips that would help a new user. Also if you have bought or made some jigs that you would recommend. Thanks, Scott Birmingham, AL Brian's Questions: Hello! I hope you all are doing well! I live in the great state of Alabama just up the road a short bit from Huy in Toney. I greatly enjoy your podcast as it is definitely the best one on the subject of woodworking! I would consider myself a hobbyist woodworker although, I have built some commissioned pieces. I have a Ridgid contractor saw mounted to the mobile stand that it came with. I use this saw for all sorts of projects, including ripping full sheets of plywood. My question is concerning the riving knife. Are there any benefits to the dang thing? I may have bent mine during a previous operation but, it seems to me that it just gets in the way and prevents me from being able to move material smoothly through the blade and is causing burning in some or most of my cuts. Also, I am using the blade that came with the saw. Should I swap to a different blade? Is the brand of blade as important as the type of blade? Thank you very much for answering my questions and I look forward to listening to many more episodes of the podcast. Juston Bohannan Huys' Questions: I thought these two might lead to some good conversations. 1. If you were to build a set of dining chairs. What is your absolute tool you couldn’t do without. Would it be a domino or would you spring for a panto router. Maybe a shaper origin. 2. Besides a captured veneered panel could you get away with 1/16 veneers on one side and 3/32 backing veneers on the other side on a panel? Essentially would you veneer a panel with different thickness of veneers on either side. Reason I ask I might make a builtin shelving unit with 1/16” veneer on the front and some 3/32 backing veneer on the back side that faces the wall. It would be captured with the cabinet carcass dado so I would assume it wouldn’t potato chip. But who knows. Jesse @ beechlandfurniture

Domino Tips, Riving Knives, Panotrouters and MUCH MORE!

Tenon Joinery

Support us on Patreon: https://www.patreon.com/woodshoplife Guys Questions: Hello fellas. I greatly appreciate your show, as its the only one that I haven’t gotten tired of over the years. I’m making a chimney cupboard for the most difficult of clients – my wife. She really dislikes, frame and panel doors and wanted solid doors. So there will be two 40 inch high by 20 inch wide – full overlay doors. I’m using beautiful air dryer sinker Cypress for the entire piece. I’ve convinced her that big slabs of solid wood doors would potentially bow or twist overtime, so I have developed an idea of making each door like this - I’ve sourced a 26 inch wide 8 foot board. after milling and cutting to 44 inch pieces, I cut the middle out to be the panel and will use the adjoining pieces for the rail and styles. The panel will be tongue and grooved to sit flush with the front with the styles - with an 1/8 inch gap. Therefore, it will be a frame and panel door, but out of one piece of wood that looks solid. My question is relating to the inside panel and its thickness. It seems if I leave it thicker (currently 5/8”) it will be more prone to twisting the frame, where if I bring it down thinner like 3/8”, it may be more prone to splitting. Please let me know your thoughts . Thank you so much. Mike Sibley Hi Gents. Love the show. I've invested in a 3 stage sprayer and have been trying it out, getting the hang of it. Any General advice to a new sprayer user? Also, while a perfect coat is the goal, would it be better to put down too much, or too little of 'sprayables'? It seems too little is much easier to fix. Usually just add another coat after it's dried. Thanks for the great show! Mark Bett Brian's Questions: Guy’s, I love the podcast and listen often but haven’t caught completely up yet. What is a good method of making mortise and tenon jointery with a router only? I’ve got a Bosch 1/2” router and intent to buy a router table too. I’ve seen various jigs on the market but was wondering what the best option is for the money having only a router, and small DEWALT 8.5” lunchbox table saw. I intend to build smaller household furniture such as side tables, nightstands and a dresser. Thanks for the advice, love the show, Dave Huffman I would love to get a subscription to a woodworking magazine for my fiance for Christmas. He's a big fan of your podcast. You have mentioned one before but now I can't find it. What are your suggestions? - Lauren Zontini Huy's Questions I have a Dewalt 733 planer and the blades are starting to go dull. I saw online where I could build a jig out of a 2x4 by cutting 2 slots at 42 degrees angles and placing my blades inside the slots. You would then run the blades over a sharpening stone to give it a new edge. Is this a good method for sharpening my blade or should I be looking for another method. Keep making this podcast and I am sure that all of us out here listening will continue to tune in and keep asking questions. Happy Holidays to all of you Cory Sorry if this is a repeat only mostly caught up. The wife wants a painted double dresser. I dislike painted furniture and prefer to work with maple or walnut but we compromised… so the wife’s getting a painted double dresser. I intend to use plywood since it’s a paint grade project but don’t have much experience with it. What’s a good construction method for plywood? I’ve got a small table saw, 1/2” router, kreg jig and hand tools. Can I get way with using the kreg jig and but joints for carcass construction? How about plywood drawers? I intend to use latex paint, should I add a top coat over it? Many Thanks, love the podcast Dave Huffman

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guys Questions: Hello fellas. I greatly appreciate your show, as its the only one that I haven’t gotten tired of over the years. I’m making a chimney cupboard for the most difficult of clients – my wife. She really dislikes, frame and panel doors and wanted solid doors. So there will be two 40 inch high by 20 inch wide – full overlay doors. I’m using beautiful air dryer sinker Cypress for the entire piece. I’ve convinced her that big slabs of solid wood doors would potentially bow or twist overtime, so I have developed an idea of making each door like this - I’ve sourced a 26 inch wide 8 foot board. after milling and cutting to 44 inch pieces, I cut the middle out to be the panel and will use the adjoining pieces for the rail and styles. The panel will be tongue and grooved to sit flush with the front with the styles - with an 1/8 inch gap. Therefore, it will be a frame and panel door, but out of one piece of wood that looks solid. My question is relating to the inside panel and its thickness. It seems if I leave it thicker (currently 5/8”) it will be more prone to twisting the frame, where if I bring it down thinner like 3/8”, it may be more prone to splitting. Please let me know your thoughts . Thank you so much. Mike Sibley Hi Gents. Love the show. I've invested in a 3 stage sprayer and have been trying it out, getting the hang of it. Any General advice to a new sprayer user? Also, while a perfect coat is the goal, would it be better to put down too much, or too little of 'sprayables'? It seems too little is much easier to fix. Usually just add another coat after it's dried. Thanks for the great show! Mark Bett Brian's Questions: Guy’s, I love the podcast and listen often but haven’t caught completely up yet. What is a good method of making mortise and tenon jointery with a router only? I’ve got a Bosch 1/2” router and intent to buy a router table too. I’ve seen various jigs on the market but was wondering what the best option is for the money having only a router, and small DEWALT 8.5” lunchbox table saw. I intend to build smaller household furniture such as side tables, nightstands and a dresser. Thanks for the advice, love the show, Dave Huffman I would love to get a subscription to a woodworking magazine for my fiance for Christmas. He's a big fan of your podcast. You have mentioned one before but now I can't find it. What are your suggestions? - Lauren Zontini Huy's Questions I have a Dewalt 733 planer and the blades are starting to go dull. I saw online where I could build a jig out of a 2x4 by cutting 2 slots at 42 degrees angles and placing my blades inside the slots. You would then run the blades over a sharpening stone to give it a new edge. Is this a good method for sharpening my blade or should I be looking for another method. Keep making this podcast and I am sure that all of us out here listening will continue to tune in and keep asking questions. Happy Holidays to all of you Cory Sorry if this is a repeat only mostly caught up. The wife wants a painted double dresser. I dislike painted furniture and prefer to work with maple or walnut but we compromised… so the wife’s getting a painted double dresser. I intend to use plywood since it’s a paint grade project but don’t have much experience with it. What’s a good construction method for plywood? I’ve got a small table saw, 1/2” router, kreg jig and hand tools. Can I get way with using the kreg jig and but joints for carcass construction? How about plywood drawers? I intend to use latex paint, should I add a top coat over it? Many Thanks, love the podcast Dave Huffman

Mortise and tenon joinery, Door construction, Sharpening and MUCH MORE!!

Support us on Patreon: https://www.patreon.com/woodshoplife   Guys Questions: Hello fellow wood shop enthusiasts! I was recently watching Guys YouTube videos of the secretary with tambour doors. He made a comment about sanding the door to I think 350, but also made a comment about treating the end grain differently so that it would not take on more oil and I assume darken it more then the face. He did not really elaborate on the technique. How is end grain treated differently when applying oil finishes and when staining? - Unkown Hey guys this is Mason from Blairswoodshop again. A follow up from the first question I asked about the jet 16-32 conveyor belt, I did what you said and now there is no more constant adjustments and it seems to work great now thank you for the help! Now for the next question. I have some really nice looking spaulted maple, as you know it's not structurally the most sound. I was thinking about maybe making it into thin veneer for box lids and things like that. I have no veneering experience or a vacuum pump, what is a cheap way to start veneering with out breaking the bank? I've been spending so much on tools last thing I need to do is go to the wife saying I need more tools haha, Thank you all for what you guys do! Look for to hear what you guys suggest. P.S. I do have everything to make the veneers just looking for diffrent ways to attach it to my work pieces. Mason Blair Brian's Questions: 1- I have a Dewalt dw735 planer and so far so good, But I noticed that if I try with a wide plank the planer makes a noise that sounds like it's too much for him to handle, how do you guys use a planer? One dimension several passes with 32s increments? - Karel Any advice for someone trying to start their own woodworking buisness? I do small crafts currently, but I plan to start selling furniture in the near future . Feel free to check out what I’m doing at the moment. - Dillon Huy's Questions: Hey guys, Do you know where I can find information on guidelines for building furniture? (i.e. website or books) For example, I'm looking to build a queen size platform bed frame with 20 inch legs and use castle joint joinery to connect the four sides to the legs. I'm trying to figure out what the minimum size the four sides, feet should be and how deep should the castle joints be? Deeper than my 10 inch table saw can cut? Thanks for all the great help. - Matt I would like to monetize my woodworking as a side business, if possible, in the future. Honestly, I am not sure if that means cutting boards or commissions, but I am leaning towards some simple stuff and seeing where it goes. I’ve thought of adding some sort of CNC to the mix. I am on the fence if I should go the route of a Shaper Origin as I can use this to make patterns for furniture projects, aid in doing some repetitive work, and do some custom accents on small items to personalize items for people or do I go the route of getting a Onefinity or other similar sized DIY CNC machine? The Onefinity would obviously take up much more room and cannot be brought to the project but could work on its own so to speak so if I am going to try and make money it can be working on something while I am doing something else. So, the part two to this question is if I go this route do you think I should get an add on laser attachment again for decorative personalization of future items to be made?

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guys Questions: Hello fellow wood shop enthusiasts! I was recently watching Guys YouTube videos of the secretary with tambour doors. He made a comment about sanding the door to I think 350, but also made a comment about treating the end grain differently so that it would not take on more oil and I assume darken it more then the face. He did not really elaborate on the technique. How is end grain treated differently when applying oil finishes and when staining? - Unkown Hey guys this is Mason from Blairswoodshop again. A follow up from the first question I asked about the jet 16-32 conveyor belt, I did what you said and now there is no more constant adjustments and it seems to work great now thank you for the help! Now for the next question. I have some really nice looking spaulted maple, as you know it's not structurally the most sound. I was thinking about maybe making it into thin veneer for box lids and things like that. I have no veneering experience or a vacuum pump, what is a cheap way to start veneering with out breaking the bank? I've been spending so much on tools last thing I need to do is go to the wife saying I need more tools haha, Thank you all for what you guys do! Look for to hear what you guys suggest. P.S. I do have everything to make the veneers just looking for diffrent ways to attach it to my work pieces. Mason Blair Brian's Questions: 1- I have a Dewalt dw735 planer and so far so good, But I noticed that if I try with a wide plank the planer makes a noise that sounds like it's too much for him to handle, how do you guys use a planer? One dimension several passes with 32s increments? - Karel Any advice for someone trying to start their own woodworking buisness? I do small crafts currently, but I plan to start selling furniture in the near future . Feel free to check out what I’m doing at the moment. - Dillon Huy's Questions: Hey guys, Do you know where I can find information on guidelines for building furniture? (i.e. website or books) For example, I'm looking to build a queen size platform bed frame with 20 inch legs and use castle joint joinery to connect the four sides to the legs. I'm trying to figure out what the minimum size the four sides, feet should be and how deep should the castle joints be? Deeper than my 10 inch table saw can cut? Thanks for all the great help. - Matt I would like to monetize my woodworking as a side business, if possible, in the future. Honestly, I am not sure if that means cutting boards or commissions, but I am leaning towards some simple stuff and seeing where it goes. I’ve thought of adding some sort of CNC to the mix. I am on the fence if I should go the route of a Shaper Origin as I can use this to make patterns for furniture projects, aid in doing some repetitive work, and do some custom accents on small items to personalize items for people or do I go the route of getting a Onefinity or other similar sized DIY CNC machine? The Onefinity would obviously take up much more room and cannot be brought to the project but could work on its own so to speak so if I am going to try and make money it can be working on something while I am doing something else. So, the part two to this question is if I go this route do you think I should get an add on laser attachment again for decorative personalization of future items to be made?

We Welcome our new Co-Host Brian! And of course we answer YOUR woodworking questions!

Support us on Patreon: https://www.patreon.com/woodshoplife   Guy 1) Hi Guy, Huy, and Sean. I have a question about prefinishing and glue. I know that the generally recommended best practice when prefinishing is to tape off any surfaces that will later be receiving glue. However, I'm building a project that is going to have basically a grid of cross lap joints, and taping off all of those surfaces sounds really annoying. If I use epoxy as my glue instead of yellow wood glue, could I get away with not taping off the glue surfaces? The joints I am making should be pretty strong, so the glue is really just there to stop things from shifting. Thanks! Matthew 2) I'm curious what you do when your local lumber store doesn't have what you want or need?  We have one hardwood dealer in town, and the next nearest supplier is 3-4 hrs away (each way).   The local place has a lot of the most common stuff, but every once in a while I hit a wall when looking for something they don't carry.  I've heard of people ordering lumber either over the phone or online and having it shipped to them.  I think Guy has mentioned calling his local store and having them deliver it to his door; I don't know if this would be a similar process, or something else entirely. Thanks, Monte   Sean 1) Hi Guys, Thank you for all the hard work you put into the podcast. It is extremely educational and very helpful. I am sure you discussed it in some form previously, but I wanted to ask if each of you can describe the equipment you use for spraying, does it handle different type of finishes (i.e. paint, poly, etc.) and would you buy the same equipment again or switch to a different one? Thank you again. Omer   Huy 1) Hi Guys, (and Guy), I wrote you a few weeks back about a glue up question. The advice that you gave was spot on. Thank You for clearing up the questions that I had on that topic. Once again, YOU GUYS ROCK! And Guy, you mentioned to place my Cherry boards outside in the sun for a day to darken them up, WOW did that do the trick! It is tips like that, that really make you guys stand out compared to other podcasts. I am on to another project now, and that is building my grand kids toy dump trucks for Christmas. Here I have another glue up question. A neighbor gave me a quart of Titebond Cold Press for Veneer glue. I was gonna try and use this like regular wood glue. I do not think this would cause any issues but I thought I would run it past all of you to see if I am missing anything. Is there an issue  with using Veneer glue like this? Cory  2) Hi guys! Awesome podcasts, as always, and thank you for answering some of my previous questions. I really appreciate the feedback that you have been able to provide. My question today is about mobility versus stability. I do the majority of my woodworking out of one half of a two car garage and I often switch between power tool focused projects and hand tool projects depending on the project. My project list, both for clients and for my wife and myself, is always changing so it seems that my work flow and my shop setup changes on a regular basis. My bench and assembly table are built on locking casters making them easily mobile, but not stable enough for serious hand tool work. How do you balance stability with mobility? Also, how do you incorporate adequate dust collection with the power tools when they are mobile? I have a 3 1/2 HP Harbor Freight dust collector with 4" hose, but I have not yet installed any fixed piping in my shop, I'm currently moving it from machine to machine. Would you recommend putting it in a corner and running pipes along the ceiling to drop down to the machines? Thank you guys, Joshua The Blackdog Woodworks

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guy 1) Hi Guy, Huy, and Sean. I have a question about prefinishing and glue. I know that the generally recommended best practice when prefinishing is to tape off any surfaces that will later be receiving glue. However, I'm building a project that is going to have basically a grid of cross lap joints, and taping off all of those surfaces sounds really annoying. If I use epoxy as my glue instead of yellow wood glue, could I get away with not taping off the glue surfaces? The joints I am making should be pretty strong, so the glue is really just there to stop things from shifting. Thanks! Matthew 2) I'm curious what you do when your local lumber store doesn't have what you want or need?  We have one hardwood dealer in town, and the next nearest supplier is 3-4 hrs away (each way).   The local place has a lot of the most common stuff, but every once in a while I hit a wall when looking for something they don't carry.  I've heard of people ordering lumber either over the phone or online and having it shipped to them.  I think Guy has mentioned calling his local store and having them deliver it to his door; I don't know if this would be a similar process, or something else entirely. Thanks, Monte Sean 1) Hi Guys, Thank you for all the hard work you put into the podcast. It is extremely educational and very helpful. I am sure you discussed it in some form previously, but I wanted to ask if each of you can describe the equipment you use for spraying, does it handle different type of finishes (i.e. paint, poly, etc.) and would you buy the same equipment again or switch to a different one? Thank you again. Omer Huy 1) Hi Guys, (and Guy), I wrote you a few weeks back about a glue up question. The advice that you gave was spot on. Thank You for clearing up the questions that I had on that topic. Once again, YOU GUYS ROCK! And Guy, you mentioned to place my Cherry boards outside in the sun for a day to darken them up, WOW did that do the trick! It is tips like that, that really make you guys stand out compared to other podcasts. I am on to another project now, and that is building my grand kids toy dump trucks for Christmas. Here I have another glue up question. A neighbor gave me a quart of Titebond Cold Press for Veneer glue. I was gonna try and use this like regular wood glue. I do not think this would cause any issues but I thought I would run it past all of you to see if I am missing anything. Is there an issue  with using Veneer glue like this? Cory 2) Hi guys! Awesome podcasts, as always, and thank you for answering some of my previous questions. I really appreciate the feedback that you have been able to provide. My question today is about mobility versus stability. I do the majority of my woodworking out of one half of a two car garage and I often switch between power tool focused projects and hand tool projects depending on the project. My project list, both for clients and for my wife and myself, is always changing so it seems that my work flow and my shop setup changes on a regular basis. My bench and assembly table are built on locking casters making them easily mobile, but not stable enough for serious hand tool work. How do you balance stability with mobility? Also, how do you incorporate adequate dust collection with the power tools when they are mobile? I have a 3 1/2 HP Harbor Freight dust collector with 4" hose, but I have not yet installed any fixed piping in my shop, I'm currently moving it from machine to machine. Would you recommend putting it in a corner and running pipes along the ceiling to drop down to the machines? Thank you guys, Joshua The Blackdog Woodworks

Host Departure, Your Woodworking Questions & MUCH More!

Great podcast! Extremely informative and entertaining. Couldn’t ask for more.

One of the best woodworking podcasts

If you’re into woodworking this podcast is a must listen.

Great podcasting

Woodshop Life Podcast

Support us on Patreon: https://www.patreon.com/woodshoplife Guy 1) I have a makita trim router with a ¼” up cut spiral bit routing a groove in the edge of a board and the collet keeps loosening the bit. I’m only taking ⅛” deep passes. Not sure what the problem is. Any help would be appreciated. Thanks, Douglas. 2) Love the show. My hobbiest shop is a 24x30 garage and I’m looking to upgrade the dust collection. I initially looked at a big 3HP dust collector and plumbing the whole shop with 4” and 6” ducting. Now I’m looking at getting 2-3  Grizzly G0785 Or Rockler wall mount units and keeping each near 1-2 machines and not running expensive and cumbersome duct work all over my shop. It seems like for about $1200 I could have a pretty effective setup by going this way instead of 1 big dust collector.   Am I missing something?  Do you see any disadvantages of going with multiple smaller units mounted close to my machines? - Ron   Sean 1) Hey guys I’ve got a workbench vise question. I’m in the process of building a new workbench and am ready to mount a front vise.   I have an old record style vise that I was going to use and mount to the apron leaving it proud. However everyone I see now mounts there vise inset using the bench apron as the rear jaws of the vise. Granted these are all quick release Lee Valley style vises.   Would you mount the vise proud or inset the vise? I found some info from Paul Sellers in favor of mounting a vise proud to avoid pinching fingers. But haven’t found any info on people using vises that are flush to the apron of the bench.   Btw this isn’t my end all be all beautiful shaker/rubo bench. It will probably last 5-7 years before I replace it.   Thanks Jesse Beechland Furniture -   2) I am a very green woodworker. I am building a small side/end table. I'll attach the top to the aprons and allow for wood movement. I want to add a shelf at about a third of the length from the top to the floor. I thought about attaching it to the legs. How would you guys do it? Thanks for the great podcast. - Omer   Huy 1) Thank you all for devoting such time to this podcast. I am a new woodworker and I am learning so much in every episode. I am writing with a question about jointing and spring joints. I refurbished an old Atlas 6000 6 inch jointer. It's a beast and I think I did a pretty good job getting everything aligned -- very sharp new blades at the right height. But when I edge-joint longer boards (60" -- the outfeed table of the jointer is only about 26"), I do get a very small, wide arch (crook or frown face) on the jointed edge. When I put two jointed boards edge to edge to make a panel, there is a small (1/32-1/16") gap in the center, but the ends of the board are flush. I lamented this to a fellow woodworker and he told me not to worry -- that it's a best practice to make a "spring joint' by leaving such a gap and closing it up via clamps during a glue-up. So my question is: is my friend right -- should I just go with a spring joint? And if he's not right, how can I calibrate my jointer so I get a straighter edge? - Adam Potthast  2) I'm going to be building a run of side chairs in the near future, and am in the design phase. My question is about the necessity of lower stretchers for durability. I'd like these chairs to last for decades (at least), and my kids/nephews are maniacs. Do lower stretchers on a side chair add measurable strength, or are the mortise/tenon joints for the seat aprons sufficient on their own? I love your podcast. Thanks very much. - Andrew

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guy 1) I have a makita trim router with a ¼” up cut spiral bit routing a groove in the edge of a board and the collet keeps loosening the bit. I’m only taking ⅛” deep passes. Not sure what the problem is. Any help would be appreciated. Thanks, Douglas. 2) Love the show. My hobbiest shop is a 24x30 garage and I’m looking to upgrade the dust collection. I initially looked at a big 3HP dust collector and plumbing the whole shop with 4” and 6” ducting. Now I’m looking at getting 2-3  Grizzly G0785 Or Rockler wall mount units and keeping each near 1-2 machines and not running expensive and cumbersome duct work all over my shop. It seems like for about $1200 I could have a pretty effective setup by going this way instead of 1 big dust collector. Am I missing something?  Do you see any disadvantages of going with multiple smaller units mounted close to my machines? - Ron Sean 1) Hey guys I’ve got a workbench vise question. I’m in the process of building a new workbench and am ready to mount a front vise. I have an old record style vise that I was going to use and mount to the apron leaving it proud. However everyone I see now mounts there vise inset using the bench apron as the rear jaws of the vise. Granted these are all quick release Lee Valley style vises. Would you mount the vise proud or inset the vise? I found some info from Paul Sellers in favor of mounting a vise proud to avoid pinching fingers. But haven’t found any info on people using vises that are flush to the apron of the bench. Btw this isn’t my end all be all beautiful shaker/rubo bench. It will probably last 5-7 years before I replace it. Thanks Jesse Beechland Furniture - 2) I am a very green woodworker. I am building a small side/end table. I'll attach the top to the aprons and allow for wood movement. I want to add a shelf at about a third of the length from the top to the floor. I thought about attaching it to the legs. How would you guys do it? Thanks for the great podcast. - Omer Huy 1) Thank you all for devoting such time to this podcast. I am a new woodworker and I am learning so much in every episode. I am writing with a question about jointing and spring joints. I refurbished an old Atlas 6000 6 inch jointer. It's a beast and I think I did a pretty good job getting everything aligned -- very sharp new blades at the right height. But when I edge-joint longer boards (60" -- the outfeed table of the jointer is only about 26"), I do get a very small, wide arch (crook or frown face) on the jointed edge. When I put two jointed boards edge to edge to make a panel, there is a small (1/32-1/16") gap in the center, but the ends of the board are flush. I lamented this to a fellow woodworker and he told me not to worry -- that it's a best practice to make a "spring joint' by leaving such a gap and closing it up via clamps during a glue-up. So my question is: is my friend right -- should I just go with a spring joint? And if he's not right, how can I calibrate my jointer so I get a straighter edge? - Adam Potthast 2) I'm going to be building a run of side chairs in the near future, and am in the design phase. My question is about the necessity of lower stretchers for durability. I'd like these chairs to last for decades (at least), and my kids/nephews are maniacs. Do lower stretchers on a side chair add measurable strength, or are the mortise/tenon joints for the seat aprons sufficient on their own? I love your podcast. Thanks very much. - Andrew

Episode 34 - Workbench Vise, Multiple Dust Collectors, Spring Joint, & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife Guys Questions: 1) Hi guys , I have been pondering this for a while and just wanted some other perspectives, if you don't mind. Question, how would you go about veneering a cabriole leg, something in the Louis 14th era. I haven't found anything on how it was done (some kind of hammer veneering I'm guessing)  I want to do this for a personal project and would appreciate any insights.  Cheers, joey chalk. 2) I have an older coffee table. Nicely made from oak. It is finished in a dark brown stain and then covered in a glossy varnish (at least I think it's a stain/varnish combination). I like the coffee table, but the finish is not my style and would prefer it to be matt and/or lighter in color . I guess the easiest work is to just get it matt by lightly sanding it and refinishing it with matt varnish? Getting the color lighter will require more sanding and more work? What would your approach be? Any suggestions for stains, oils or another finishes that look natural/lighter?  Thank you! Bart (from Belgium) Seans Questions: 1) I was wondering your thoughts about putting a wax finish over danish oil. I’ve heard that it’s more upkeep and unnecessary. I’ve finished a few small gift boxes made out of walnut with danish oil but I feel that I don’t quite get the patina I'm looking for. Do you have a favorite finish for small gift boxes? - Scott 2) Hi Guys, Thanks for putting together such a great podcast! I know that Guy has a 12" jointer/planer combo machine and believe Huy and Sean may also. I've asked Guy a few questions about his machine in the past and he has been kind enough to answer and even do a review of his machine...thanks Guy! I am looking to eventually purchase a similar machine to Guy's, but the Canadian importer I will purchase from offers both 12" and 16" models. Has there been a time that you've wished for a machine larger than 12"? Obviously the 16" is more money, an extra $1000 or so. Would you go for the 16", or is 12" more than enough? - Kreg Huys Questions: 1) I always here people talk about how you can’t trust the square you just bought to be square. Well, if nothing I have is square, then how the hell do I know what is actually square? This question of what is really square and what is not has been screwing with me for a couple of years now. So I just pass over it and get my stuff close enough.... which, of course, makes for its own set of headaches....PyratWoodworking 2) Loving the podcast guys! My question is regarding third party upgrades to bigger machines. Recently found a used Jet JJ-6CSX on marketplace for pretty cheap ($550) and the commercial contractor selling it must not have used it because it’s in amazing condition. That being said, I’m tempted to upgrade the cutter head. Although the knives are functional and fine, I know that a helical head has a lot more long term benefits. So my question is: Have any of you upgraded a cutterhead from a third party vendor before? If so, how did it work out? I have also only been able to find a couple of options from Grizzly or Byrd. Are there others out there that also make something that can fit this model and what should I be weary of when looking? As always thanks for all you guys do. Joey Winter Wolf Woodworking   Our Social Picks: Sean: @StudioCSH Guy: @retiredwithwood Huy:  @fernwehwoodworking

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guys Questions: 1) Hi guys , I have been pondering this for a while and just wanted some other perspectives, if you don't mind. Question, how would you go about veneering a cabriole leg, something in the Louis 14th era. I haven't found anything on how it was done (some kind of hammer veneering I'm guessing) I want to do this for a personal project and would appreciate any insights. Cheers, joey chalk. 2) I have an older coffee table. Nicely made from oak. It is finished in a dark brown stain and then covered in a glossy varnish (at least I think it's a stain/varnish combination). I like the coffee table, but the finish is not my style and would prefer it to be matt and/or lighter in color . I guess the easiest work is to just get it matt by lightly sanding it and refinishing it with matt varnish? Getting the color lighter will require more sanding and more work? What would your approach be? Any suggestions for stains, oils or another finishes that look natural/lighter? Thank you! Bart (from Belgium) Seans Questions: 1) I was wondering your thoughts about putting a wax finish over danish oil. I’ve heard that it’s more upkeep and unnecessary. I’ve finished a few small gift boxes made out of walnut with danish oil but I feel that I don’t quite get the patina I'm looking for. Do you have a favorite finish for small gift boxes? - Scott 2) Hi Guys, Thanks for putting together such a great podcast! I know that Guy has a 12" jointer/planer combo machine and believe Huy and Sean may also. I've asked Guy a few questions about his machine in the past and he has been kind enough to answer and even do a review of his machine...thanks Guy! I am looking to eventually purchase a similar machine to Guy's, but the Canadian importer I will purchase from offers both 12" and 16" models. Has there been a time that you've wished for a machine larger than 12"? Obviously the 16" is more money, an extra $1000 or so. Would you go for the 16", or is 12" more than enough? - Kreg Huys Questions: 1) I always here people talk about how you can’t trust the square you just bought to be square. Well, if nothing I have is square, then how the hell do I know what is actually square? This question of what is really square and what is not has been screwing with me for a couple of years now. So I just pass over it and get my stuff close enough.... which, of course, makes for its own set of headaches....PyratWoodworking 2) Loving the podcast guys! My question is regarding third party upgrades to bigger machines. Recently found a used Jet JJ-6CSX on marketplace for pretty cheap ($550) and the commercial contractor selling it must not have used it because it’s in amazing condition. That being said, I’m tempted to upgrade the cutter head. Although the knives are functional and fine, I know that a helical head has a lot more long term benefits. So my question is: Have any of you upgraded a cutterhead from a third party vendor before? If so, how did it work out? I have also only been able to find a couple of options from Grizzly or Byrd. Are there others out there that also make something that can fit this model and what should I be weary of when looking? As always thanks for all you guys do. Joey Winter Wolf Woodworking Our Social Picks: Sean: <a href="https://www.instagram.com/StudioCSH" rel="nofollow" target="_blank">@StudioCSH</a> Guy: <a href="https://www.instagram.com/retiredwithwood" rel="nofollow" target="_blank">@retiredwithwood</a> Huy:  <a href="https://www.instagram.com/fernwehwoodworking" rel="nofollow" target="_blank">@fernwehwoodworking</a>

Episode 31 - Refinishing, Wax over Danish Oil, When Square is Square, & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife   Guy: 1) Hi Guys, been thinking a lot lately on getting into woodworkering. I follow several instagram and YouTube channels but just wanted to get some input on what i need to get started and what are some really nice projects for a complete beginner to start off with. -acam22 2) Gentleman, thank you for answering my question in Episode 7. Ive got a new question for you. Blade Cleaning versus Blade Sharpening. We all know it’s a good practice the clean blades regularly and personally I go with some warm water and simple green, it’s worked great for me. My question is, what are the signs I should look for when I’m beyond this simple solution and it’s time to get my blades sharpened. Thanks and keep up the good work! -Hubble_workshop   Sean: 1) How do you like the jet combo jointer/thickness planer? I’m space limited and thinking of replacing a 6” ridgid jointer and 10” inca combo machine. I’d like to have a larger jointer and was wondering how you like the combination machine. Did you consider other similar models?  Thanks - Adam 2) I recently acquired 120 bf of ash and thought it would be perfect to make a new office desk. I was thinking of making a metal base with ash top and ash cabinets underneath. There would be a single cabinet box on either side. I was thinking of making the cabinet box out of solid ash. Is this a good idea? Any concerns or should I still to plywood? The reason for ash would be to keep consistent wood/grain/color throughout. And the fact I have a lot of it. If solid wood is ok, any recommendations on box construction? Thanks! - crwoodshop   Huy: 1) Is there a distinct advantage to a cast iron router surface over a laminate one? The price difference seems negligible between the two.    Is there anything that we should consider specifically when getting a router table wing/insert with regards to fence and dust collection? For example, Saw Stop looks like it uses a proprietary fence that doesn't have dust collection at the fence. We're trying to "future-proof" our shop as best we can, so we don't want to be limited by being stuck to a single solution with regards to fences. Our plan is to put a JessEm Mast-R Lift II in whatever wing we get with the Porter Cable 7518.   Thanks for the awesome podcast. By far my favorite wood working podcast and something we look forward to every time we see a new episode release. Keep up the good work!   Chris and Lydia   2) I'm planning on building a few cedar shutters. I want to maintain the original wood color as much as possible and prevent the cedar from graying over time. What finish would you recommend that would both protect the wood from rain/sunlight and also prevent the wood from graying too quickly?   Thanks! - Josh

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guy: 1) Hi Guys, been thinking a lot lately on getting into woodworkering. I follow several instagram and YouTube channels but just wanted to get some input on what i need to get started and what are some really nice projects for a complete beginner to start off with. -acam22 2) Gentleman, thank you for answering my question in Episode 7. Ive got a new question for you. Blade Cleaning versus Blade Sharpening. We all know it’s a good practice the clean blades regularly and personally I go with some warm water and simple green, it’s worked great for me. My question is, what are the signs I should look for when I’m beyond this simple solution and it’s time to get my blades sharpened. Thanks and keep up the good work! -Hubble_workshop Sean: 1) How do you like the jet combo jointer/thickness planer? I’m space limited and thinking of replacing a 6” ridgid jointer and 10” inca combo machine. I’d like to have a larger jointer and was wondering how you like the combination machine. Did you consider other similar models?  Thanks - Adam 2) I recently acquired 120 bf of ash and thought it would be perfect to make a new office desk. I was thinking of making a metal base with ash top and ash cabinets underneath. There would be a single cabinet box on either side. I was thinking of making the cabinet box out of solid ash. Is this a good idea? Any concerns or should I still to plywood? The reason for ash would be to keep consistent wood/grain/color throughout. And the fact I have a lot of it. If solid wood is ok, any recommendations on box construction? Thanks! - crwoodshop Huy: 1) Is there a distinct advantage to a cast iron router surface over a laminate one? The price difference seems negligible between the two. <ol><li> Is there anything that we should consider specifically when getting a router table wing/insert with regards to fence and dust collection? For example, Saw Stop looks like it uses a proprietary fence that doesn't have dust collection at the fence. We're trying to "future-proof" our shop as best we can, so we don't want to be limited by being stuck to a single solution with regards to fences. Our plan is to put a JessEm Mast-R Lift II in whatever wing we get with the Porter Cable 7518.</li> </ol> Thanks for the awesome podcast. By far my favorite wood working podcast and something we look forward to every time we see a new episode release. Keep up the good work! Chris and Lydia 2) I'm planning on building a few cedar shutters. I want to maintain the original wood color as much as possible and prevent the cedar from graying over time. What finish would you recommend that would both protect the wood from rain/sunlight and also prevent the wood from graying too quickly? Thanks! - Josh

Episode 33 - Solid Wood Cabinets, Blade Cleaning, Finishing Cedar, & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife   Guy 1) Have you ever made your own plywood from solid wood for projects?  I’m thinking a void free core of walnut plywood could allow me to use it in projects where the edge could be exposed unlike traditional veneered plywood and also give me some dimension stability.  You thoughts? Tips? Brian 2) I know at least one of you uses the Leigh dovetail jig. Just wondering how well the jig is made. If the tail and pin boards align, and if there is a lot of tweaking to get the jig to work properly. I have Porter Cable 4216 jig. I have been trying to get this to work for a case I am working on. I was having some problems with the tails and pins being about a sixteenth out of alignment. I took many measurements to be sure that the tail board is centered in the template only to discover as I loosened the template it could shift side to side by more that a thirty second of an inch. There are a few other things I am not crazy about with this jig. Just wondering what your experiences have shown using other jigs,   Also, thanks for answering all of my previous questions! - Dave Sean 1) I have been a weekend woodworker for 5 or so years as time permits with 3 kids and a busy schedule. I am working out of a 3 car garage that my wife and I both park in. I use about 1.5 bays currently and when I do not have a project I move equipment so I can park. I do not have an assembly or outfeed table to work from and often use the garage floor. Frustrating... I am looking for space savings option for a table, preferably one with dog holes so I can clamp to route, biscuit joint, and other assembly work. I currently do not have hand tools i.e. handsaws, planes, or chisels for heavy duty hand tool work. Maybe one that is portable like Guys outfeed table as I have an incra tablesaw fence as well. I don't know if a festool mft3 would be a solution as I could store it when not working/assembling. Maybe a storabe outfeed table as well as a storable assemble might work. I don't think I am ready for a hand tool workbench yet. My father in law had a production cabinet door and counter top shop with a large industrial CNC machine and could cut a festoool style top out of MDF that would not cost me anything out of pocket. Is that a good option? Any recommendations would be appreciated. 2) Shhhh.... don’t let Guy know I asked another question. Let’s just say this one is from Boudreaux François... hahaha With as many jigs and templates that are made for your projects through the years what do you do with them? Do you make them one time, use them then toss them out or repurpose them for other jigs? Aside from the obvious ones that are traditionally used in the shop (cross cut sleds, tapering jig, edge jointing jig for the table saw... etc) at what point do you say “I’m going to keep this one”. I have always struggled with the idea of spending the time to make these jigs and templates even if I know that I won’t necessarily be using it again in the next 6 months then just trashing it. Just curious. As always, Thank you for your time and please keep up the absolutely wonderful work y’all are doing on the podcast and your shops! The information y’all share is always spot on! Thanks, Brent Jarvis Clean Cut Woodworking   Huy 1) I am making a pair of side tables that are based on Philip Morley's table design from the #275 Fine woodworking issue. I've scaled it down and modified it to be a side table more than a dining table (proportionally shrunk all the dimensions, increased apron size to fit a shallow drawer in it and added a low shelf) but I am trying to keep a similar look to his original piece. So, I am using his techniques to create the legs which have a curved taper and Phil achieves this shape with a two-sided jig that he runs along a flush cut trim bit. My legs are 2 and 5/16 thick at the thickest part. Add on about 1/2 inch for the jig and that meant I needed to get a pretty tall flush cut bit. I bought a flush cut bit (top and bottom bearing) that is 2 and 1/2 inches long (2 and 1/2 cutting length, 3/4 wide, 1/2 shank, overall length 4 and 7/8) so that I could route it in one pass. I will set it up on the router table and I intend to cut real close to the line so I don't have much material to remove, but I am still a little nervous about it when I think about that tall bit. I have never used such a large bit before and would like to know what special considerations to take. Should I be concerned about the stability of the bit when it is that tall? 2) Hello again, some advice/brainstorming sought. I am building a puzzle building table. If you are unfamiliar, it is essentially a large box with a very shallow bottom so that a puzzle can be built on that surface. Two large leaves then fold over from the ends to cover the entire top, leave a table for other use.  Because of the leaves unfolding and draping over the short ends, I need the end to be flush across, so a normal leg with the rails mortised in won't really work as insetting the rail isn't possible with the hinges, and flush (to me) won't look right. The ones I've seen on the internet build a big box then attach the legs inside the corners. I'd also like the legs to be removable so that it can be transported more compact as it will be "pub height" of about 40" I'm wondering what attachment method you might use to lace the legs on the inside corners, preferably removable, but also sturdy and non wracking. The rails will be about 8" wide (still designing) with the "bottom" about an inch from the top. So there will be about 6-7" available corner space underneath the top for the legs to rest. Any ideas? Thanks, Peter @mr.downing.woodworking on Instagram Our social media picks: Sean:  @thosmoser Guy: @pdindy Huy: @meredithhartfurniture   Thanks to the sponsor of this episode, Maverick Abrasives 

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guy 1) Have you ever made your own plywood from solid wood for projects?  I’m thinking a void free core of walnut plywood could allow me to use it in projects where the edge could be exposed unlike traditional veneered plywood and also give me some dimension stability.  You thoughts? Tips? Brian 2) I know at least one of you uses the Leigh dovetail jig. Just wondering how well the jig is made. If the tail and pin boards align, and if there is a lot of tweaking to get the jig to work properly. I have Porter Cable 4216 jig. I have been trying to get this to work for a case I am working on. I was having some problems with the tails and pins being about a sixteenth out of alignment. I took many measurements to be sure that the tail board is centered in the template only to discover as I loosened the template it could shift side to side by more that a thirty second of an inch. There are a few other things I am not crazy about with this jig. Just wondering what your experiences have shown using other jigs, Also, thanks for answering all of my previous questions! - Dave Sean 1) I have been a weekend woodworker for 5 or so years as time permits with 3 kids and a busy schedule. I am working out of a 3 car garage that my wife and I both park in. I use about 1.5 bays currently and when I do not have a project I move equipment so I can park. I do not have an assembly or outfeed table to work from and often use the garage floor. Frustrating... I am looking for space savings option for a table, preferably one with dog holes so I can clamp to route, biscuit joint, and other assembly work. I currently do not have hand tools i.e. handsaws, planes, or chisels for heavy duty hand tool work. Maybe one that is portable like Guys outfeed table as I have an incra tablesaw fence as well. I don't know if a festool mft3 would be a solution as I could store it when not working/assembling. Maybe a storabe outfeed table as well as a storable assemble might work. I don't think I am ready for a hand tool workbench yet. My father in law had a production cabinet door and counter top shop with a large industrial CNC machine and could cut a festoool style top out of MDF that would not cost me anything out of pocket. Is that a good option? Any recommendations would be appreciated. 2) Shhhh.... don’t let Guy know I asked another question. Let’s just say this one is from Boudreaux François... hahaha With as many jigs and templates that are made for your projects through the years what do you do with them? Do you make them one time, use them then toss them out or repurpose them for other jigs? Aside from the obvious ones that are traditionally used in the shop (cross cut sleds, tapering jig, edge jointing jig for the table saw... etc) at what point do you say “I’m going to keep this one”. I have always struggled with the idea of spending the time to make these jigs and templates even if I know that I won’t necessarily be using it again in the next 6 months then just trashing it. Just curious. As always, Thank you for your time and please keep up the absolutely wonderful work y’all are doing on the podcast and your shops! The information y’all share is always spot on! Thanks, Brent Jarvis Clean Cut Woodworking Huy 1) I am making a pair of side tables that are based on Philip Morley's table design from the #275 Fine woodworking issue. I've scaled it down and modified it to be a side table more than a dining table (proportionally shrunk all the dimensions, increased apron size to fit a shallow drawer in it and added a low shelf) but I am trying to keep a similar look to his original piece. So, I am using his techniques to create the legs which have a curved taper and Phil achieves this shape with a two-sided jig that he runs along a flush cut trim bit. My legs are 2 and 5/16 thick at the thickest part. Add on about 1/2 inch for the jig and that meant I needed to get a pretty tall flush cut bit. I bought a flush cut bit (top and bottom bearing) that is 2 and 1/2 inches long (2 and 1/2 cutting length, 3/4 wide, 1/2 shank, overall length 4 and 7/8) so that I could route it in one pass. I will set it up on the router table and I intend to cut real close to the line so I don't have much material to remove, but I am still a little nervous about it when I think about that tall bit. I have never used such a large bit before and would like to know what special considerations to take. Should I be concerned about the stability of the bit when it is that tall? 2) Hello again, some advice/brainstorming sought. I am building a puzzle building table. If you are unfamiliar, it is essentially a large box with a very shallow bottom so that a puzzle can be built on that surface. Two large leaves then fold over from the ends to cover the entire top, leave a table for other use. Because of the leaves unfolding and draping over the short ends, I need the end to be flush across, so a normal leg with the rails mortised in won't really work as insetting the rail isn't possible with the hinges, and flush (to me) won't look right. The ones I've seen on the internet build a big box then attach the legs inside the corners. I'd also like the legs to be removable so that it can be transported more compact as it will be "pub height" of about 40" I'm wondering what attachment method you might use to lace the legs on the inside corners, preferably removable, but also sturdy and non wracking. The rails will be about 8" wide (still designing) with the "bottom" about an inch from the top. So there will be about 6-7" available corner space underneath the top for the legs to rest. Any ideas? Thanks, Peter @mr.downing.woodworking on Instagram Our social media picks: Sean:  <a href="https://www.instagram.com/thosmoser" rel="nofollow" target="_blank">@thosmoser</a> Guy: <a href="https://www.instagram.com/pdindy" rel="nofollow" target="_blank">@pdindy</a> Huy: <a href="https://www.instagram.com/meredithhartfurniture" rel="nofollow" target="_blank">@meredithhartfurniture</a> Thanks to the sponsor of this episode, <a href="https://www.maverickabrasives.com/" rel="nofollow" target="_blank">Maverick Abrasives</a>

Episode 32 - The Perfect Assembly Table, Router Bit Safety, Making Your Own Plywood, & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife   Guys Questions 1) Can you speak a little in general about expansion and contraction of wood with some basic Do Not vs. Do when it comes to glueing and allowing wood movement?  Thanks in advance, I am learning a ton! April 2) Hey Guys, I’ve got a question for the podcast that I’ve never heard anyone address. Is it worth it to invest in high-dollar drill bits?  As a hobbiest on a tight budget, I generally get new bits at the box store, but sometimes I can look at them while they are spinning, and tell that they are not spinning straight. They seem to do the job, but I always wondered if having better bits (or possibly a better drill, I guess) is worth the money? Thanks, and love the great show format. Sincerely, Scott A. Jackson, TN   Sean's Questions 1) Hello, I would like your opinion what would be the better upgrade option around the 300-400 dollar range. I currently have a 60's era Delta 6" jointer with a 1.5HP motor and am debating on whether I should upgrade to a carbide helical cutter head or should I upgrade my capacity with a used 8" jointer which I can usually find around here for about a hundred more. Thanks for the podcast, it's going great! - Travis 2) Love your podcast. Your show is amazing and I love all three of your social stuff. Guy, your YouTube page is amazingly helpful for me. I'm a hobbiest woodworker who sells pieces based upon commission only. I've been building out my shop via commissioned projects over the past 4 years. I started with all HD Ryobi stationary tools to learn on and now am upgrading to more professional tools. Here's what I have so far: Laguna F2 hybrid table saw, just got it and love it, it took some mods for dust collection but it's awesome. Wen drill press. Craftsman used lathe(got it for $100 from a neighbor) basically brand new. Rigid miter saw station. Porter and cable router on a homemade table. Dust collection system with a shop vac and dust deputy. 10 inch wen band saw. My question is what do I get next? Drum sander? Or planer/jointer combo? My budget is around $1200 and space is an issue. I work in a 1 car garage. I do have everything on wheels except the table saw. Hope I didn't ramble. Keep up the great work. Brad  Huy's Questions 1) What glue do you use for veneering? Are there any circumstances when you would change the glue your using, such as curved panels, color of veneer, or purchased vs shop sawn veneer? Douglas   2) I don’t think I have heard y’all talk about these before so here you go. Woodpecker tools. What do y’all think of them?  Are there better or cheaper tools out there that will work as good? I have a few Woodpecker tools and I really like them and find them very useful but just looking for other options out there. I also have bought a few of their one time tools and have been very pleased with them. Keep up the great work guys! - Troy   Thanks to Maverick Abrasives for sponsoring this episode!

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guys Questions 1) Can you speak a little in general about expansion and contraction of wood with some basic Do Not vs. Do when it comes to glueing and allowing wood movement?  Thanks in advance, I am learning a ton! April 2) Hey Guys, I’ve got a question for the podcast that I’ve never heard anyone address. Is it worth it to invest in high-dollar drill bits?  As a hobbiest on a tight budget, I generally get new bits at the box store, but sometimes I can look at them while they are spinning, and tell that they are not spinning straight. They seem to do the job, but I always wondered if having better bits (or possibly a better drill, I guess) is worth the money? Thanks, and love the great show format. Sincerely, Scott A. Jackson, TN Sean's Questions 1) Hello, I would like your opinion what would be the better upgrade option around the 300-400 dollar range. I currently have a 60's era Delta 6" jointer with a 1.5HP motor and am debating on whether I should upgrade to a carbide helical cutter head or should I upgrade my capacity with a used 8" jointer which I can usually find around here for about a hundred more. Thanks for the podcast, it's going great! - Travis 2) Love your podcast. Your show is amazing and I love all three of your social stuff. Guy, your YouTube page is amazingly helpful for me. I'm a hobbiest woodworker who sells pieces based upon commission only. I've been building out my shop via commissioned projects over the past 4 years. I started with all HD Ryobi stationary tools to learn on and now am upgrading to more professional tools. Here's what I have so far: Laguna F2 hybrid table saw, just got it and love it, it took some mods for dust collection but it's awesome. Wen drill press. Craftsman used lathe(got it for $100 from a neighbor) basically brand new. Rigid miter saw station. Porter and cable router on a homemade table. Dust collection system with a shop vac and dust deputy. 10 inch wen band saw. My question is what do I get next? Drum sander? Or planer/jointer combo? My budget is around $1200 and space is an issue. I work in a 1 car garage. I do have everything on wheels except the table saw. Hope I didn't ramble. Keep up the great work. Brad  Huy's Questions 1) What glue do you use for veneering? Are there any circumstances when you would change the glue your using, such as curved panels, color of veneer, or purchased vs shop sawn veneer? Douglas 2) I don’t think I have heard y’all talk about these before so here you go. Woodpecker tools. What do y’all think of them?  Are there better or cheaper tools out there that will work as good? I have a few Woodpecker tools and I really like them and find them very useful but just looking for other options out there. I also have bought a few of their one time tools and have been very pleased with them. Keep up the great work guys! - Troy Thanks to <a href="https://www.maverickabrasives.com/" rel="nofollow" target="_blank">Maverick Abrasives</a> for sponsoring this episode!

Episode 36 - Veneer Glue, Capacity or Helical Cutter, Cheap Bits & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife   Guys Questions 1) I’m having trouble getting clean 45 degree angles (or any angle other than 90) on my table saw. I use an Incra Miter 1000. It seems like my workpiece shifts ever so slightly as the wood enters the blade and my miter isn’t clean. I don’t have confidence in the miter stop provided with the miter gauge cause it’s just a small round piece of metal. Any tips on cutting angles with this style miter gauge would be awesome. Also, do you recommend using it on the left or right miter slot of a left tilting blade. Much appreciated.  Keep up the good work. -Zach   2) I just got my first Lie-Nielsen plane (#4 bronze body smoother).  I've decided it's time to up my sharpening game and purchase some quality stones to sharpen plane irons and chisels.  I had pretty much decided on Shapton Waterstones when I ran across their glass stones. The glass stones now seem to be the way to go but I'd like to have your guys take on glass vs. water stones before I pull the trigger. Love the show guys!  Thanks and Merry Christmas! - Jeff   Sean's Questions 1) Hello guys, big fan of the podcast, I've listened to all your episodes and look forward to each one. I enjoy the Q&amp;A format. My question is about a workbench I want to build, more specifically the top. I have no formal workbench right now so I'm looking to build my first. I was initially looking to source some butcher block top and use that but last year I acquired a full 4x8 sheet of 1-1/4" MDF leftover from a jobsite. I had to rip it down and cut it down to make it manageable enough to get it in my car so I have 2 5'x2' pieces of 1-1/4" MDF. I was planning on laminating these 2 pieces together to get a 5' X 2' X 2-1/2" thick benchtop. I'm wondering what if any issues I may encounter and any tips for gluing up, attaching a vise, etc. I was going to drill dog holes but I recently saw a video from Dave Piccuito at https://youtu.be/DYIwSm2wnAA where he puts in a t-track. I really like how his turned out and was thinking about doing that. So I was just hoping to get some insight into anything I may want to look out for or be aware of. Pros/cons/thoughts. Thanks for everything you do guys, take care. - Michael 2) On a recent episode, you talked about using your CNC's to cut out jigs, etc.  I'm interested in getting a CNC to complement my woodworking, which is a fairly new hobby for me since I retired a couple of years ago.  My only real interest is in using it to make jig parts and router templates for things like furniture legs - not interested in creating final products or 3D sculptures with the CNC, nor doing production for products to sale.  What are your recommendations (size, features, manufacturers) for a setup that would see light duty limited to this application? I've tried some of the online laser-cutting services - but they can get pricey pretty quick and have limited thicknesses, so I'm interested in my own setup.  Price is a big consideration - as I can't see spending 5 grand for such a limited application. Thanks, Scott Huy's Questions 1) I started woodworking last year, and I've only been using jatoba, African mahogany, hickory, and hard maple. Mostly because I got good deals on Craigslist. Based on what I've heard you guys discussing, those might not be the easiest woods to work with. My next project is to make a bed for my 4 year old son. What species would make my life easier? I'm in Denver, so cherry isn't all that cheap. Also, any tips on making beds? -aaron 2) I have a commission for a 6’ round 12/4 (poplar but it doesn’t matter) dining table. I’ll fabricate the steel base, but how would you move such a massive piece around the shop? And any recommendations on the glue up? Guy, how do you move your large pieces at the new shop? Thanks gentlemen! Will Thanks to Maverick Abrasives for sponsoring this episode! 

Support us on Patreon: <a href="https://www.patreon.com/woodshoplife" rel="nofollow" target="_blank">https://www.patreon.com/woodshoplife</a> Guys Questions 1) I’m having trouble getting clean 45 degree angles (or any angle other than 90) on my table saw. I use an Incra Miter 1000. It seems like my workpiece shifts ever so slightly as the wood enters the blade and my miter isn’t clean. I don’t have confidence in the miter stop provided with the miter gauge cause it’s just a small round piece of metal. Any tips on cutting angles with this style miter gauge would be awesome. Also, do you recommend using it on the left or right miter slot of a left tilting blade. Much appreciated.  Keep up the good work. -Zach 2) I just got my first Lie-Nielsen plane (#4 bronze body smoother).  I've decided it's time to up my sharpening game and purchase some quality stones to sharpen plane irons and chisels.  I had pretty much decided on Shapton Waterstones when I ran across their glass stones. The glass stones now seem to be the way to go but I'd like to have your guys take on glass vs. water stones before I pull the trigger. Love the show guys!  Thanks and Merry Christmas! - Jeff Sean's Questions 1) Hello guys, big fan of the podcast, I've listened to all your episodes and look forward to each one. I enjoy the Q&amp;A format. My question is about a workbench I want to build, more specifically the top. I have no formal workbench right now so I'm looking to build my first. I was initially looking to source some butcher block top and use that but last year I acquired a full 4x8 sheet of 1-1/4" MDF leftover from a jobsite. I had to rip it down and cut it down to make it manageable enough to get it in my car so I have 2 5'x2' pieces of 1-1/4" MDF. I was planning on laminating these 2 pieces together to get a 5' X 2' X 2-1/2" thick benchtop. I'm wondering what if any issues I may encounter and any tips for gluing up, attaching a vise, etc. I was going to drill dog holes but I recently saw a video from Dave Piccuito at<a href="https://youtu.be/DYIwSm2wnAA" rel="nofollow" target="_blank"> https://youtu.be/DYIwSm2wnAA</a> where he puts in a t-track. I really like how his turned out and was thinking about doing that. So I was just hoping to get some insight into anything I may want to look out for or be aware of. Pros/cons/thoughts. Thanks for everything you do guys, take care. - Michael 2) On a recent episode, you talked about using your CNC's to cut out jigs, etc.  I'm interested in getting a CNC to complement my woodworking, which is a fairly new hobby for me since I retired a couple of years ago.  My only real interest is in using it to make jig parts and router templates for things like furniture legs - not interested in creating final products or 3D sculptures with the CNC, nor doing production for products to sale.  What are your recommendations (size, features, manufacturers) for a setup that would see light duty limited to this application? I've tried some of the online laser-cutting services - but they can get pricey pretty quick and have limited thicknesses, so I'm interested in my own setup.  Price is a big consideration - as I can't see spending 5 grand for such a limited application. Thanks, Scott Huy's Questions 1) I started woodworking last year, and I've only been using jatoba, African mahogany, hickory, and hard maple. Mostly because I got good deals on Craigslist. Based on what I've heard you guys discussing, those might not be the easiest woods to work with. My next project is to make a bed for my 4 year old son. What species would make my life easier? I'm in Denver, so cherry isn't all that cheap. Also, any tips on making beds? -aaron 2) I have a commission for a 6’ round 12/4 (poplar but it doesn’t matter) dining table. I’ll fabricate the steel base, but how would you move such a massive piece around the shop? And any recommendations on the glue up? Guy, how do you move your large pieces at the new shop? Thanks gentlemen! Will Thanks to <a href="https://www.maverickabrasives.com/" rel="nofollow" target="_blank">Maverick Abrasives</a> for sponsoring this episode!

Episode 35 - Perfect Miters, CNC Machines, Moving Large Pieces, & MUCH More!

What is this?
1 quote, 3 ideas & 1 question from a carefully curated podcast episode.
Every Monday & Wednesday.

Want a 3rd insight and episode every week? Email me at curation@owltail.com.

OwlTail

OwlTail 1-3-1

The best podcast episodes on parenting. Interviewing experts and talking through common issues surrounding parenting. This topic is filled with important lessons and insights for anyone listening. Add episodes you're interested into your queue below!