Carter Stanfield's guest appearances

Carter Stanfield

HVAC School - For Techs, By Techs

Kevin Hart

Bill Johnson

Ruth King

Chris Stephens

Dan Holohan

John Ellis

Bill Spohn

Jack Rise

Andy Holt

Jerry Eavenson

Nate Adams

David Richardson

Jim Bergmann

Jim Loring

Jamie Kitchen

OwlTail

Carter tells us why compression ratio is important, what it means, why it changes so much on heat pump systems, and the effect it has on system operation. We also talk a bit more about heat pumps and their unique challenges beyond compression ratio. Compression ratio is a comparison of discharge pressure to suction pressure. A ratio of 3:1 indicates that the discharge pressure is three times higher than the suction pressure. The higher the pressure difference, the less gas you move and the less efficient your system is. The compressor has a fixed volume, but the gas's actual mass varies based on density and pressure. So, lower suction pressure results in less gas being moved. Dirty filters, coils, and other means of clogging the system can drastically increase the compression ratio. Heat pumps are especially sensitive to compression ratio changes because they move varying amounts of refrigerant depending on the operating mode. As such, charging heat pumps can be a challenge. Some heat pump manufacturers use a charge compensator to help make charging a slightly less difficult task. Heat pumps may also have coils with smaller surface areas, which can drive up the compression ratio. Heat pumps have highly variable evaporator temperatures, and refrigeration systems have highly variable condensing temperatures. Both of these highly variable conditions may indicate systems with susceptibility to high compression ratios. In the case of refrigeration systems, the metering devices are critical components for reducing keeping the compression ratios at bay. If you cannot find manufacturer literature or are working on an old heat pump, Carter recommends using airflow and temperature difference to determine how much heating the system is accomplishing. Carter and Bryan also discuss:  Rheem and Ruud heat pumps Centrifugal blowers Plenum placement New inverter-driven compressors If you have an iPhone, subscribe to the podcast  HERE, and if you have an Android phone, subscribe  HERE.

Carter tells us why compression ratio is important, what it means, why it changes so much on heat pump systems, and the effect it has on system operation. We also talk a bit more about heat pumps and their unique challenges beyond compression ratio. Compression ratio is a comparison of discharge pressure to suction pressure. A ratio of 3:1 indicates that the discharge pressure is three times higher than the suction pressure. The higher the pressure difference, the less gas you move and the less efficient your system is. The compressor has a fixed volume, but the gas's actual mass varies based on density and pressure. So, lower suction pressure results in less gas being moved. Dirty filters, coils, and other means of clogging the system can drastically increase the compression ratio. Heat pumps are especially sensitive to compression ratio changes because they move varying amounts of refrigerant depending on the operating mode. As such, charging heat pumps can be a challenge. Some heat pump manufacturers use a charge compensator to help make charging a slightly less difficult task. Heat pumps may also have coils with smaller surface areas, which can drive up the compression ratio. Heat pumps have highly variable evaporator temperatures, and refrigeration systems have highly variable condensing temperatures. Both of these highly variable conditions may indicate systems with susceptibility to high compression ratios. In the case of refrigeration systems, the metering devices are critical components for reducing keeping the compression ratios at bay. If you cannot find manufacturer literature or are working on an old heat pump, Carter recommends using airflow and temperature difference to determine how much heating the system is accomplishing. Carter and Bryan also discuss: <ul> <li>Rheem and Ruud heat pumps</li> <li>Centrifugal blowers</li> <li>Plenum placement</li> <li>New inverter-driven compressors</li> </ul>If you have an iPhone, subscribe to the podcast <a href="https://itunes.apple.com/us/podcast/hvac-school-for-techs-by-techs/id1155660740?mt=2" rel="nofollow" target="_blank"> HERE</a>, and if you have an Android phone, subscribe <a href="http://www.stitcher.com/podcast/bryan-orr-3/hvac-school" rel="nofollow" target="_blank"> HERE</a>.

Compression Ratio, Heat Pumps and More w/ Carter Stanfield

Carter Stanfield, a co-author of  Fundamentals of HVACR, talks about the entire refrigeration circuit. He also explains how to read and plot a pressure-enthalpy diagram. The refrigeration circuit has four main components: evaporator, compressor, condenser, and metering device. When teaching, Carter likes to explain that boiling is a cooling process and condensation is a heating process. He describes saturation as the breaking point at which liquid refrigerant can no longer hold more heat (in the evaporator). The superheated vapor from the suction line then enters the compressor; the compressor adds even more superheat. So, the discharge line has very superheated vapor. In the condenser, saturation occurs when the vapor cools to the point that it can no longer hold more moisture; the temperature stays the same until the refrigerant becomes entirely liquid. Subcooled liquid travels to the metering device via the liquid line. The metering device reduces the pressure of the refrigerant and feeds the evaporator. However, some flash gas occurs and helps drop the temperature of the remaining liquid. A pressure-enthalpy diagram illustrates the refrigerant's changes in and out of the saturated state as it moves through the refrigeration circuit. The chart looks like a curved dome, and saturated states are inside the dome. Pressure is on the y-axis, and enthalpy is on the x-axis. Pressure is a logarithmic arrangement; a linear arrangement would be impossible to plot. The bottom of the chart shows low pressures, and the top shows high ones. Enthalpy is the heat content of the refrigerant. We express it in BTUs/lb. When you plot one of these diagrams, you can start with four lines and readings: high and low-side pressure, suction line temperature into the compressor, and liquid line temperature into the metering device. You will end up drawing a parallelogram shape on the chart.If you have an iPhone, subscribe to the podcast  HERE, and if you have an Android phone, subscribe HERE.

Carter Stanfield, a co-author of <a href="https://www.amazon.com/Fundamentals-HVACR-3rd-Carter-Stanfield/dp/0134016165" rel="nofollow" target="_blank"> Fundamentals of HVACR</a>, talks about the entire refrigeration circuit. He also explains how to read and plot a pressure-enthalpy diagram. The refrigeration circuit has four main components: evaporator, compressor, condenser, and metering device. When teaching, Carter likes to explain that boiling is a cooling process and condensation is a heating process. He describes saturation as the breaking point at which liquid refrigerant can no longer hold more heat (in the evaporator). The superheated vapor from the suction line then enters the compressor; the compressor adds even more superheat. So, the discharge line has very superheated vapor. In the condenser, saturation occurs when the vapor cools to the point that it can no longer hold more moisture; the temperature stays the same until the refrigerant becomes entirely liquid. Subcooled liquid travels to the metering device via the liquid line. The metering device reduces the pressure of the refrigerant and feeds the evaporator. However, some flash gas occurs and helps drop the temperature of the remaining liquid. A pressure-enthalpy diagram illustrates the refrigerant's changes in and out of the saturated state as it moves through the refrigeration circuit. The chart looks like a curved dome, and saturated states are inside the dome. Pressure is on the y-axis, and enthalpy is on the x-axis. Pressure is a logarithmic arrangement; a linear arrangement would be impossible to plot. The bottom of the chart shows low pressures, and the top shows high ones. Enthalpy is the heat content of the refrigerant. We express it in BTUs/lb. When you plot one of these diagrams, you can start with four lines and readings: high and low-side pressure, suction line temperature into the compressor, and liquid line temperature into the metering device. You will end up drawing a parallelogram shape on the chart.If you have an iPhone, subscribe to the podcast <a href="https://itunes.apple.com/us/podcast/hvac-school-for-techs-by-techs/id1155660740?mt=2" rel="nofollow" target="_blank"> HERE</a>, and if you have an Android phone, subscribe <a href="http://www.stitcher.com/podcast/bryan-orr-3/hvac-school" rel="nofollow" target="_blank">HERE</a>.

The Basic Refrigeration Circuit, Pressure & Enthalpy w/ Carter Stanfield